Denver HVAC Repair

HVAC equipment is estimated to last about 15 to 20 years. Yet over the years, parts go out and need to be repaired. Heat sensors, exchangers, and ducts can become worn out. Air conditioning motors may need repairing from time to time. For repairs to your heating and air conditioning systems, and even general maintenance, let HomeAdvisor help. Enter your zip code and let us connect you with prescreened HVAC repair services near you.
Through our relationship with Wells Fargo Financial National Bank, Edwards Heating & Air offers a variety of rewarding options for financing your new Carrier product or system with approved credit.  We facilitate your investment in quality solutions to home comfort without straining your monthly budget.  With convenient monthly payments, competitive interest rates, flexible financing terms, and online account management, you can answer an unexpected need, enjoy superior equipment, and take advantage of innovative features that best suit your home and lifestyle.  Carrier financing allows you to save existing funding sources, like a home equity line of credit, credit card or bank account, for other needs or emergencies.  To learn more about financing options, or to hear about special financing promotions, contact Edwards Heating & Air and speak to an informed and helpful member of our team.
In very dry climates, evaporative coolers, sometimes referred to as swamp coolers or desert coolers, are popular for improving coolness during hot weather. An evaporative cooler is a device that draws outside air through a wet pad, such as a large sponge soaked with water. The sensible heat of the incoming air, as measured by a dry bulb thermometer, is reduced. The temperature of the incoming air is reduced, but it is also more humid, so the total heat (sensible heat plus latent heat) is unchanged. Some of the sensible heat of the entering air is converted to latent heat by the evaporation of water in the wet cooler pads. If the entering air is dry enough, the results can be quite substantial.
I'm very glad that I found another guy to come replace the circuit board and put it away from the water, fix the water leak, and also find and fix another impending failure.  All of that was for much less than HVAC Service wanted to charge for repair or replacement. The other guy did a great repair, so I'm confident it will not break down again, but if it does, I will not call HVAC Service. Don't get suckered by their Yelp Deal.
As you would expect, air conditioning in Portland isn't as expensive as in most areas of the country, owing simply to the fact that most homes don't require particularly large or state-of-the-art units. While our data suggests the national average for air conditioning installation is about $6,000, in Portland we see numbers between $3,000-$4,000, although we've also seen projects as low as $1,500 and as high as $6,000. Heat pump installation is likely to be closer to the national average, but as mentioned, these devices work to be cool your home in the summer and heat in the winter.

We are service professionals! As licensed contractors and specialists in the field of heating and air conditioning, we have the tools, the equipment, and the experience to keep your equipment running smoothly all year long. If it is emergency service that you need, we are available to assist you! To help reduce service emergencies, we offer service agreements to keep your comfort system running at peak performance.


An air conditioner's filters, coils, and fins require regular maintenance for the unit to function effectively and efficiently throughout its years of service. Neglecting necessary maintenance ensures a steady decline in air conditioning performance while energy use steadily increases. Check out our Energy Saver 101 Infographic: Home Cooling for more ways to help improve your comfort and the efficiency of your air conditioner.
If you have a good HVAC contractor they should offer an annual preventive maintenance agreement where they will perform semi-annual maintenance, once in the Spring and once in the Fall, to service your heating and cooling system. The typical maintenance agreement usually guarantees the HVAC contractor will provide service and parts at a discount rate if the listed equipment fails. Some contractors will even give you after hours service with no extra overtime charge as is the case with most other customers.

5) Check certifications. Many HVAC professionals belong to the Air Conditioning Contractors of America (ACCA) or the Sheet Metal and Air Conditioning Contractors’ National Association (SMACNA). Both sites provide listings of HVAC contractors by area. Look for contractors whose technicians are certified by North American Technician Excellence (NATE) and partnered with ENERGY STAR.


"Friendly, professional, responded quickly to my problem. I have called many air conditioning companies about my problem including the maker of the unit and had come to the conclusion that I would not find someone to repair this unit. D's came in and within a short test found the problem and assured me of a fix. They made the fix within 2 days as they needed to get a part and they also checked to see what the cost would be of the fix by putting in the control boarrd from the maker which was very high to the extreme. I now have a unit working and am very pleased."

Brubaker Inc. is a registered Pennsylvania home improvement contractor (license #4191) and holds property and workers’ compensation insurance at levels appropriate not merely for residential work, but also for commercial and industrial projects. Brubaker Inc. is a member of the Lancaster County Code Association, the ABC Keystone Chapter, and The Lancaster Chamber of Commerce & Industry. This means you can trust that we are committed to providing the highest level of service to our community.


As an Atlanta resident, you’re well aware that the weather in our area can go through extremes of both hot and cold throughout the year, taxing your heating and cooling system to its limits. You’ll likely encounter the need for repair or replacement at some point. If you need HVAC installation, HVAC maintenance, or HVAC service and repair, R.S. Andrews is the most trusted name in Atlanta.
Van Haaften Plumbing & Heating offers furnace service appointments that help keep your furnace in tip-top shape and operating efficiently for you all year long. Whether that’s discovering small issues before they become big problems, identifying potential safety hazards or making sure you’re staying in line with your manufacturer’s warranty, our experts have you covered. Our trained technicians complete furnace service with care, checking a number of components in and around your equipment. In fact, our multi-point inspection can help make sure your system operates smoothly all winter long.
Although your AC may continue to work for a time, if you ignore warning signs of air conditioner repair troubles, it can be much more costly to repair in the long term. Diminished cooling capacity not only makes your home uncomfortably warm, but it also raises your utility bills significantly as your unit struggles to maintain the desired temperature ineffectively. A system put under strain is likely to overheat, resulting in major damage. Therefore, it is best to have your air conditioner repaired promptly when you discover signs of trouble. 

Air conditioners often use a fan to distribute the conditioned air to an occupied space such as a building or a car to improve thermal comfort and indoor air quality. Electric refrigerant-based AC units range from small units that can cool a small bedroom, which can be carried by a single adult, to massive units installed on the roof of office towers that can cool an entire building. The cooling is typically achieved through a refrigeration cycle, but sometimes evaporation or free cooling is used. Air conditioning systems can also be made based on desiccants (chemicals which remove moisture from the air) and subterraneous pipes that can distribute the heated refrigerant to the ground for cooling.[2]
5) Your air conditioner is short cycling. It is perfectly normal for your air conditioner to cycle on and off to maintain a set temperature throughout your home. However, if you notice that it is turning on and off more frequently than usual and the outside temperature is not particularly warmer than normal, it is possible that your unit is malfunctioning. Short cycling puts extra stress on your air conditioner, and can cause it to fail entirely if not handled quickly. 
Need Air Conditioner Repair or Furnace Repair? Look no further. The HVAC experts at Allatoona Heating and Air are here to help you today. We have the training and experience necessary to handle all sorts of heating and air conditioning issues for all brands of heating and air equipment. We’re not limited to repairs either. Our HVAC technicians can help you with repairs, service, maintenance, replacement or installation of heating and air conditioning equipment for your home or office. Call us today!
A heating, ventilation and air conditioning (HVAC) service technician starts an appointment with a customer by asking about any problems with the heating, ventilation, and/or air conditioning systems in the client's home or business. From there, the technician will carefully examine the equipment in question to diagnose and troubleshoot the problem. Once the issue is determined, the technician provides the customer with a repair quote and, if authorized, begins to repair or replace defective equipment, mechanical components, or wiring in HVAC systems. An HVAC service technician might also be called upon by a customer to carry out preventative maintenance tasks or inspections to ensure that heating, ventilation, and air conditioning systems continue to run smoothly. A technician should have certification or an associate's degree from a technical or trade school that is accredited by HVAC Excellence, the National Center for Construction Education and Research, or the Partnership for Air Conditioning, Heating, and Refrigeration Accreditation. Formal training programs can last anywhere from six months up to two years. The job involves working with electrical equipment, so it is very important that a technician know exactly what he or she is doing or the job can get very dangerous very quickly. If an education is not in the picture, it is sometimes possible to go through a formal apprenticeship program which can take three to five years and mixes on-the-job experience and training with classroom instruction. Exams for certifications are offered by a number of associations. A license to work as an HVAC technician is required in several states and can be obtained by passing a written test. (Copyright 2018 PayScale.com)
The Chartered Institution of Building Services Engineers is a body that covers the essential Service (systems architecture) that allow buildings to operate. It includes the electrotechnical, heating, ventilating, air conditioning, refrigeration and plumbing industries. To train as a building services engineer, the academic requirements are GCSEs (A-C) / Standard Grades (1-3) in Maths and Science, which are important in measurements, planning and theory. Employers will often want a degree in a branch of engineering, such as building environment engineering, electrical engineering or mechanical engineering. To become a full member of CIBSE, and so also to be registered by the Engineering Council UK as a chartered engineer, engineers must also attain an Honours Degree and a master's degree in a relevant engineering subject.
Wow! These guys rock! I had issues with our fireplace for a while and the last company who "fixed" the issue basically charged me a lot of money and literally left me standing in the cold. Next they said it would cost me over $700 to fix the whole thing and they never came back. Finally I was able to find some good guys to fix the issue. Tony and Paul from HVAC were not only really friendly, they diagnosed the issue really fast and fixed it the same day. And it was 7 times less than what the other company asked for!!! Next time I know who to call! 5 Stars!
San Jose, CA ServicesLOWE'S OF CENTRAL SAN JOSE - Bathroom Design and RemodelAll Weather Roofing. Roofing Contractor - San Jose, CACuong's Carpet Cleaning. Carpet Cleaner - San Jose, CAE Z Home. Landscaping Company - San Jose, CACrown Plumbing. Plumber - San Jose, CAGardens Alive Landscape MaintenenceMarcone Appliance PartsJet Dry Carpet CleaningPatrick Ross ConstSwat Pest ControlAwr DumpstersTron Air
At R&R Heating & Air Conditioning, we’re proud of our reputation built on honesty, quality and service. Our family-owned and operated company has been serving Orland Park, Tinley Park, Palos, Oak Lawn and surrounding communities since 1986. Our goal is to help you create and maintain a healthy indoor climate in your home or commercial building. Using our high-efficiency HVAC systems, you’ll use less energy, cut down on utility costs and live and work in comfortable interior spaces year-round.
AC air handler squealing or grinding noises. Though most air handlers have direct-drive motors, some older units may be belt-driven. Squealing sounds from a belt-drive air handler generally occur when the belt that connects the motor to the blower slips. In most cases, the belt is improperly aligned or worn and needs replacement. Follow the instructions above under Air Conditioner Not Blowing Air and refer to your owner’s manual.
They were quick to come out and diagnose the problem with my furnace, but I thought the estimate of $549 a bit high to replace the circuit board.  So called around and found Leo's Appliance in Concord that sells appliance parts and the circuit board was only $90.49 - that is the retail cost to me, so I imagine the wholesale cost is a lot less.  So BEWARE of this company since they wanted $500!!! to replace the circuit board which is located right in the front of the furnace - extremely easy to access.  I hate it that you cannot trust repair companies.
Should I repair or replace my HVAC? It’s a common question — and you need to weigh several factors to make the decision. One of the most significant factors is the lifespan of your unit. According to EnergyStar — a U.S. Environmental Protection Agency voluntary program — an A.C. unit lasts about 15 to 20 years. On average, a heat pump perseveres for 16 years and a furnace functions for between 15 to 20 years, reports This Old House.
Your system is 10 - 15 years old: Follow this simple rule of thumb from Energy Star—if your current system is over 10 years old, it's time to start looking into an HVAC replacement. Most HVAC systems last for about 15 years, so there’s no immediate need to replace yours if it’s still functioning properly. But by doing your research now, you’ll know just what you want to do should your HVAC system suddenly stop working properly.

The use of furnaces, space heaters, and boilers as a method of indoor heating could result in incomplete combustion and the emission of carbon monoxide, nitrogen oxides, formaldehyde, volatile organic compounds, and other combustion byproducts. Incomplete combustion occurs when there is insufficient oxygen; the inputs are fuels containing various contaminants and the outputs are harmful byproducts, most dangerously carbon monoxide, which is a tasteless and odorless gas with serious adverse health effects.[14]
You have an incredible team! My suite has had major issues constant backups. In the last few months we had a horrible flood that caused us thousands of dollars in repairs. Your team was so attentive and took care of all the repairs. Just yesterday another back up called them immediately and like quick responders they were there to take of it! A huge thank you from my La Costa providers and staff! We appreciate your hard and dedicated work!
I could not have been more pleased with the responsiveness, considerate employees, workmanship, and follow up. We used three divisions of Bill Howe when we had a flood due to a water heater/T&P gauge, Plumbing, Remediation and Reconstruction. It was timely, reasonably priced and finished with attention to detail. Ashley in the office was always polite and responsive and we could not have been happier under the circumstances.

Outside of your home is an outdoor unit, which is called a condenser. Inside the condenser is a compressor, a condenser coil, and a large fan. The compressor pumps cool refrigerant to an evaporator coil located either in the air handler or just outside the furnace. The evaporator coil gets really cold so that when the blower or furnace pushes warm air past it, the air is cooled. This cool air is then distributed throughout your home through a series of air ducts. Heat is absorbed by the evaporator coil, which warms the refrigerant moving through the coils. This warm refrigerant is then pumped back outside to the condenser coil, where a giant fan cools it off allowing the warm air to escape. This cycle is repeated until your thermostat detects that your home has reached the temperature you set it to.
AC air handler buzzing sounds. Do you hear a buzzing sound when you turn on the thermostat? The only thing that comes on in the house when you turn on the thermostat is the fan relay and fan in the air handler or furnace. Try switching the thermostat HEAT/COOL switch to OFF. Then switch the fan switch from AUTO to ON. The fan (only) should come on. If the air handler makes a buzzing sound, it probably has a bad fan relay or, more likely, blower fan.
Believe it or not, the evaporator coils inside the AHU (Air Handling Unit) are freezing. You may notice the refrigerant lines on the condenser or at the AHU are frozen with ice build-up. The frost or ice builds up on the evaporator coils and blocks air flow (low air flow and no cooling are a sign of a low charge). A low refrigerant charge will cause the evaporator coil to operate at or below freezing. Since the coil typically operates below the dew point, it draws condensation out of the air. When the evaporator coil begins operating below freezing all this condensation freezes to the evaporator coil and the unit stops cooling.
Here’s a simple test to try on your own: When it’s hotter than 80 degrees outside, turn on your AC unit, and set it to well below room temperature. Let it run for 15 minutes, then use a thermometer to check just outside the return duct (the area where air flows in to be cooled). Now take a temperature reading just outside the strongest, most easily accessible vent (where cool air should be flowing out). Subtract the second reading from the first. If the difference between these two is fewer than 14 degrees, your HVAC unit might need work. 

A dehumidifier is an air-conditioner-like device that controls the humidity of a room or building. It is often employed in basements which have a higher relative humidity because of their lower temperature (and propensity for damp floors and walls). In food retailing establishments, large open chiller cabinets are highly effective at dehumidifying the internal air. Conversely, a humidifier increases the humidity of a building.
There is nothing worse than having your air conditioner break in the middle of a long, hot summer. You can ensure your air conditioning unit stays in working order all year long with regular service. Sometimes, however, repairs are necessary whether it’s fixing the evaporator, capacitor, or condenser or recharging the refrigerant. Most air conditioner repairs cost between $163 and $528 with most homeowners reporting that they spend about $344. If you do need a repair, here is some information to help you get it done quickly, professionally, and economically.
James Harrison's first mechanical ice-making machine began operation in 1851 on the banks of the Barwon River at Rocky Point in Geelong, Australia. His first commercial ice-making machine followed in 1853, and his patent for an ether vapor compression refrigeration system was granted in 1855. This novel system used a compressor to force the refrigeration gas to pass through a condenser, where it cooled down and liquefied. The liquefied gas then circulated through the refrigeration coils and vaporized again, cooling down the surrounding system. The machine produced 3,000 kilograms (6,600 lb) of ice per day.[citation needed]

I originally took off one star because of the SNAFU with getting the part ordered. When Alberto called me on the phone he admitted the person had "gotten busy with other things" and apologized. THAT was taking the high road and I was impressed by that. Sadly, for reasons I won't guess at, Alberto has decided to take the low road in his comments and imply that they got the part as quickly as possible. Well, we called at 2:30 so did someone spend six and a half hours finding the part?? That seems very doubtful. As for the price I think my review was fair in stating what value we got for what I deemed to be a slightly higher price than others might charge. I did not take any stars off for the price, and still am not, but I am taking another star off because of Alberto's comments, which are deceptive and not the same thing he told me in person. Alberto, I suggest you stick with the high road in the future.
As an Atlanta resident, you’re well aware that the weather in our area can go through extremes of both hot and cold throughout the year, taxing your heating and cooling system to its limits. You’ll likely encounter the need for repair or replacement at some point. If you need HVAC installation, HVAC maintenance, or HVAC service and repair, R.S. Andrews is the most trusted name in Atlanta.

Hii need you guys help! Once my thermostat drop below the set temp , my furnace does not turn on and I was wondering what’s wrong with it. It happens mostly on cold nights. Sometimes I would have to go in the basement and turned the furnace power switch off then on and will come on once I switch it off then on.i also change the thermostat recently, so I don’t think that’s the problem
In 1906, Stuart W. Cramer of Charlotte was exploring ways to add moisture to the air in his textile mill. Cramer coined the term "air conditioning", using it in a patent claim he filed that year as an analogue to "water conditioning", then a well-known process for making textiles easier to process. He combined moisture with ventilation to "condition" and change the air in the factories, controlling the humidity so necessary in textile plants. Willis Carrier adopted the term and incorporated it into the name of his company.[10]
Activewear & Athletic ShoesMen's Activewear,Men's Athletic Shoes,Wo...23828 CyclingBikes,Clothing & Footwear,Parts & Access...721 Exercise & FitnessBalance & Recovery,Books & Magazines,Car...5093 Fan ShopMemorabilia,MLB,NASCAR,NBA,NCAA,NFL,NHL...4359 Golf ProductsGolf Accessories,Golf Bags and Carts,Gol...352 OutdoorsAction Sports,Boats & Water Sports,Campi...10461
We’re located in Pella and service the surrounding area, so feel free to swing by if you’re looking for a new furnace or want to set up an appointment to have one of our techs do a consultation at your home and help you learn which system is ideal for your home. Schedule furnace repair or a furnace service appointment with Van Haaften Plumbing & Heating using our online scheduler, or if you want help more urgently, give us a call at 641-628-3621. 
Tony from HVAC came out on Sunday morning and did a fantastic job of immediately diagnosing the issue, quickly fixing the problem, and honoring the coupons I had. When I initially called on Saturday morning, I had a lot of trouble with their answering service getting their wires crossed with their technicians. However, Tony called me back and made it right. He even pointed out an issue that is in the horizon that I should look at (without charging me extra or telling me I had to fix it right now). Great service!
Should you experience a system breakdown, know that there are a few common causes of summer AC repairs. Below you’ll find a few of the most common ones AC repair technicians face each day throughout the warmer months. Having a better understanding of the troubles your system may face can help you feel more at ease with the AC repair process, and better comprehend the information given to you by your technician.

Other than mineral deposits, the most common problem is sediment in the water supply. The float inlet valve has a tiny hole that easily clogs. The float is usually made of plastic, and if cracked will fill with water and sink. The valve will be stuck open and the reservoir will overflow. Use caution when scraping deposits off the float. If the deposits cannot be removed, replace the float or it will sink and cause an overflow.

You’re constantly repairing your HVAC: If your heating and cooling system has needed repairs more than once or twice in the past few years, it may be time to take the leap with a replacement system. The money you spend repairing older equipment can often be better used towards the purchase of newer, energy-efficient HVAC systems. Here’s a simple guide: If your labor and parts cost upwards of $1,000, look toward replacement. 
The use of CFC as a refrigerant was once common, including the refrigerants R-11 and R-12 (sold under the brand name Freon-12). Freon refrigerants were commonly used during the 20th century in air conditioners due to their superior stability and safety properties. When they are released accidentally or deliberately, these chlorine-bearing refrigerants eventually reach the upper atmosphere.[60] Once the refrigerant reaches the stratosphere, UV radiation from the Sun homolytically cleaves the chlorine-carbon bond, yielding a chlorine radical. These chlorine radicals catalyze the breakdown of ozone into diatomic oxygen, depleting the ozone layer that shields the Earth's surface from strong UV radiation. Each chlorine radical remains active as a catalyst until it binds with another radical, forming a stable molecule and quenching the chain reaction.
We’re here to make your life a lot less hectic, and a lot more productive. As a local HVAC and Mechanical Contractor, MacDonald-Miller is committed to delivering true peace of mind. We perform regular inspections and maintenance of your building systems to ensure a greater level of operational excellence. We test, align, calibrate, and record performance to ensure your building’s equipment quality and reduce downtime or emergencies. When it comes to dedicated HVAC service & maintenance, MacDonald-Miller is unmatched.
The employees were on time, professional, and extremely thorough while addressing a particularly difficult situation. The entire time Saul, the supervisor of the team, kept me informed, and educated me about any process that I may have not completely understood. The team was courteous to the residents they encountered, and made sure not to leave evidence that they had even been there. Great job!
Did your furnace suddenly stop working? Call Coolray and relax! Our skilled HVAC technicians can repair all makes and models of furnaces, heat pumps and heating equipment. We serve Cumming, GA with 24-hour heating repair service that you can count on when you need it. Our technicians will arrive on time and will be equipped with the tools necessary to correctly diagnose and repair your heating system. Just need routine maintenance on your furnace? We can do that too. Looking for a new system altogether? We're the HVAC contractor Cumming, Georgia residents can count on for all of their home heating needs!
We have been using Bill Howe Plumbing's service for more than 25 years and have been pleasantly surprised at how consistently they perform an excellent service call. We use them for our home and our rental properties, and their dispatchers and technicians have always been the best at problem solving; our tenants have told us how great the service is as well. When we needed air conditioning service, naturally we called Bill Howe first. There's no reason to call anyone else. I know the job will be done right the first time, with fair pricing and professional service.

SEER is related to the coefficient of performance (COP) commonly used in thermodynamics and also to the Energy Efficiency Ratio (EER). The EER is the efficiency rating for the equipment at a particular pair of external and internal temperatures, while SEER is calculated over a whole range of external temperatures (i.e., the temperature distribution for the geographical location of the SEER test). SEER is unusual in that it is composed of an Imperial unit divided by an SI unit. The COP is a ratio with the same metric units of energy (joules) in both the numerator and denominator. They cancel out, leaving a dimensionless quantity. Formulas for the approximate conversion between SEER and EER or COP are available.[34]

We pride ourselves on only hiring experts who are qualified at the height of their skill, as well as friendly, approachable, and trustworthy. Past clients have described our technicians as “just good, trustworthy, honest individuals” and “very courteous and very informative as to how my inspection was going...I liked his personality!” Peachtree Service Experts in Mableton makes an effort to pair technicians with families, and it isn’t out of the ordinary to have the same expert servicing your home for years in a row. Relationships between the customer and our company are important to us, and we don’t hire anyone that we wouldn’t want to have working in our own homes.
As much as half of the energy used in your home goes to heating and cooling. So making smart decisions about your home's heating, ventilating, and air conditioning (HVAC) system can have a big effect on your utility bills — and your comfort. Take these steps to increase the efficiency of your heating and cooling system. For more information, see our Guide to Energy Efficient Heating & Cooling (708KB).
Your heating, cooling, and air quality systems are a significant investment, and are expected to answer high demand, day after day, year after year.  To enjoy the greatest benefit from your equipment, let the professionals from Edwards Heating & Air handle the essential upkeep.  Through conscientious, seasonal maintenance, we effectively restore operational sound and efficiency levels, improve air quality, eliminate the majority of repairs, and extend service life.  The key to safe and uninterrupted performance, lower overall costs, and superior temperature control is through proactive measures.  The NATE-certified technicians from Edwards Heating & Air complete a lengthy task list that is specifically targeted at the optimization of your system.  Not only will your HVAC system be ready and able to handle volatile weather conditions, but it will operate safely.  Comprehensive service from Edwards Heating & Air is your best protection against health concerns, property damage, system failure, and elevated cost of ownership.  Contact Edwards Heating & Air, and we'll set up a maintenance plan that is affordable, convenient, rewarding, and works perfectly for you.
Reinstall the access panel and disconnect block. Turn on the circuit breaker and furnace switch. Then set the thermostat to a lower temperature and wait for the AC to start (see “Be Patient at Startup,” below). The compressor should run and the condenser fan should spin. If the compressor starts but the fan doesn’t, the fan motor is most likely shot. Shut off the power and remove the screws around the condenser cover. Lift the cover and remove the fan blade and motor (photo 7). Reinstall the blade and secure the cover. Then repower the unit and see if the fan starts. If it doesn’t, you’ve given it your best shot—it’s time to call a pro.
×