Denver HVAC Repair

Other than mineral deposits, the most common problem is sediment in the water supply. The float inlet valve has a tiny hole that easily clogs. The float is usually made of plastic, and if cracked will fill with water and sink. The valve will be stuck open and the reservoir will overflow. Use caution when scraping deposits off the float. If the deposits cannot be removed, replace the float or it will sink and cause an overflow.
If so, you may want to consider replacing your entire AC system. After your AC system reaches a certain age, it makes more sense to invest in a new AC system altogether rather than repairing it one piece at a time. To learn more about John Moore’s AC replacement program, our warranty, and the cost-advantages of replacing your AC system, visit our AC Replacement page.
Never fails when you have guests! Always a plumbing issue pops up! First time I have called Bill Howe. Shower knob was frozen & we couldn't budge it. Really nice looking & polite young man named Marcus showed up promptly. He proceeded to look at problem. He explained problem & possible options if part was not easily replaceable. Fortunately the faucet was fixed with a replacement part without complications. Great news since the shower is 43 yrs. old!! Experience was very positive & I highly recommend this company!! Young repairman could not have been nicer or more professional. Will definitely recommend them.
This time we had a major issue with our sewage line related to roots. Was terrible. But we called Billy Howe and Mike came and did an Incredible job. Not only he explained really well what was going on but he was careful and knowledgeable. I was so relief that not only we trust in BH team but we were lucky that was Mike coming to execute the service.
If you hear clicking that is followed by a hum or buzz, you’re probably hearing the fan motor attempting to start without the boost it needs from the capacitor. You can almost always conclude that the capacitor has failed. Sometimes you can get the compressor fan spinning (clockwise) by pushing it with a thin stick or long screwdriver poked through the grille. But the chances are good that this might work for one cycle, but the capacitor will fail next time the AC goes on. It’s best to replace the capacitor.

Our technicians have experience repairing furnaces and will make sure your home is back to keeping you comfortable in no time. From training and certifications to our reputation for getting the job done right time and time again, you can be sure that Van Haaften Plumbing & Heating’s furnace repair technicians will have your troubles taken care of and your furnace running smoothly. Whether it’s emergency furnace repair or service you can schedule some time in advance, our team can provide you peace of mind, knowing that your furnace is in skilled hands. Need a furnace repair? When performing a repair, it's vital to source professional HVAC contractors.
The HVAC industry is a worldwide enterprise, with roles including operation and maintenance, system design and construction, equipment manufacturing and sales, and in education and research. The HVAC industry was historically regulated by the manufacturers of HVAC equipment, but regulating and standards organizations such as HARDI, ASHRAE, SMACNA, ACCA, Uniform Mechanical Code, International Mechanical Code, and AMCA have been established to support the industry and encourage high standards and achievement.
Poor dehumidification can also be caused by excessive humidity in the home. This may be caused by water leaks or open windows during humid periods or by a lack of proper condensate drainage from your evaporator coil in the furnace's plenum. A properly functioning cooling unit produces condensate and drains it away. If your unit is not producing condensate its cooling and dehumidification functions are not working properly.
So, whether you need a furnace repair or you’re searching for a new heating and cooling system—or you need a plumbing repair as soon as possible–you can count on our specialists in Longmont. We’re experts in heating system and plumbing repair and providing top-notch heating and plumbing service is what we do best. Call Service Experts 24/7/365 at 303-647-5749 or request an appointment online today, and don’t forget to look at our coupons page for savings on your heating system or plumbing repair service.

Two weeks go by and no phone call from HVAC Service regarding install date, or any update at all.  I call them to check in to see if they have put me on the schedule and when I can expect to have the AC installed.    You can tell by the discussion I had with the lady on the phone that they completely forgot about me and have not scheduled anything.  She says she needs to get in contact with the owner because she has no idea on the availability of the crane.  I was told that she would call me back by the end of the day with an update.  Surprise, surprise, no phone call.  
The changing seasons take a toll on your HVAC equipment. Unfortunately, it always seems that your aging furnace gives up in the middle of a cold snap and your AC unit sputters out during the hottest day of summer. These events are more than an annoyance: they can quickly turn into emergencies when your home reaches extreme temperatures. That's when it's time to call in your local ARS®/Rescue Rooter® HVAC specialist, who has the training to get to the root of any heating, ventilation or air conditioning problem quickly.

While there's nothing you can do to guarantee your air conditioner or furnace will never need repairs, there are ways to take better care of your system. Changing out the air filters every 3-6 months, making sure nothing is obstructing or interfering with the outside unit, and keeping all vents unblocked in well-used rooms will help keep your air conditioning and heating system operating efficiently.


The installment team ARS made numerous attempts to correct the issue over the last several months. They have not found the issue on why my 2018 outside unit and inside unit (4 ton unit) is not cooling the house down. I had the unit for 1 year and in the months of July and August the Nest unit reads 90 degrees from 12 noon to 7pm. My wife and I are very upset with the upgrade unit we purchase from Home Depot.

Call Miller's Air Conditioning & Heating at (925) 583-6387 and always speak with a live and helpful member of our team, who will immediately focus on your requirements.  While our competitors punch a strict time clock, we realize heating and cooling challenges often arise outside of regular business hours.  Rather than leave a message on a machine, take advantage of personalized service and the prompt response of radio dispatched trucks.
Ground source, or geothermal, heat pumps are similar to ordinary heat pumps, but instead of transferring heat to or from outside air, they rely on the stable, even temperature of the earth to provide heating and air conditioning. Many regions experience seasonal temperature extremes, which would require large-capacity heating and cooling equipment to heat or cool buildings. For example, a conventional heat pump system used to heat a building in Montana's −70 °F (−57 °C) low temperature or cool a building in the highest temperature ever recorded in the US—134 °F (57 °C) in Death Valley, California, in 1913 would require a large amount of energy due to the extreme difference between inside and outside air temperatures. A few feet below the earth's surface, however, the ground remains at a relatively constant temperature. Utilizing this large source of relatively moderate temperature earth, a heating or cooling system's capacity can often be significantly reduced. Although ground temperatures vary according to latitude, at 6 feet (1.8 m) underground, temperatures generally only range from 45 to 75 °F (7 to 24 °C).
Modern air conditioning emerged from advances in chemistry during the 19th century, and the first large-scale electrical air conditioning was invented and used in 1902 by England inventor Willis Carrier. The introduction of residential air conditioning in the 1920s helped enable the great migration to the Sun Belt in the United States.[citation needed]

Modern air conditioning systems are not designed to draw air into the room from the outside, they only recirculate the increasingly cool air on the inside. Because this inside air always has some amount of moisture suspended in it, the cooling portion of the process always causes ambient warm water vapor to condense on the cooling coils and to drip from them down onto a catch tray at the bottom of the unit from which it must then be routed outside, usually through a drain hole. As this moisture has no dissolved minerals in it, it will not cause mineral buildup on the coils. This will happen even if the ambient humidity level is low. If ice begins to form on the evaporative fins, it will reduce circulation efficiency and cause the development of more ice, etc. A clean and strong circulatory fan can help prevent this, as will raising the target cool temperature of the unit's thermostat to a point that the compressor is allowed to turn off occasionally. A failing thermistor may also cause this problem. Refrigerators without a defrost cycle may have this same issue. Dust can also cause the fins to begin blocking air flow with the same undesirable result: ice.
My A/C went out on a Friday and I found this company in the phone book on Saturday morning. They came out just a few hours later and it was decided that I needed a new system. The pricing was good as well as the customer service. They brought me a temporary portable air conditioner for Saturday night and they replaced my system on Sunday. This company has the best customer service of any business that I have dealt with. I would highly recommend this company to anyone and have. Great Company!!!!!
Our skilled technicians arrive prepared to handle the scope of even complex malfunctions, with all makes and models of heating and cooling equipment, most often resolving the problem on the spot.  For all your HVAC service, repairs, and installations in Livermore, CA, Pleasanton, CA & Dublin, CA, call the team from Miller’s Air Conditioning & Heating!
Ductwork pinging or popping. If you hear a pinging or popping sound coming from metal ductwork, this may be caused by thermal expansion or by air blowing past a loose flap of metal. Track along the duct runs, listening for the sound. If you find it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
Our skilled technicians arrive prepared to handle the scope of even complex malfunctions, with all makes and models of heating and cooling equipment, most often resolving the problem on the spot.  For all your HVAC service, repairs, and installations in Livermore, CA, Pleasanton, CA & Dublin, CA, call the team from Miller’s Air Conditioning & Heating!
Your HVAC professional can perform a yearly tune-up of your system for around $80-$100. This yearly maintenance can go far toward heading off major repairs to your system, and provide you with peace of mind and considerable savings in the long term. Additionally, regular servicing of your AC unit can help a home inspector to certify that your unit is working properly in the event you decide to sell your home.
I have no idea what a barrel is??? In chilled water systems the evaporator and condensers sometimes use what is called a chiller barrel for the evaporator and/or the condenser but for most residential system it is a rarity to find a chilled water system installed. Are you talking about a commercial system chiller. 7.1 KW is not a very big system but they do exist in light commercial and as mentioned in residential.
The first air conditioners and refrigerators employed toxic or flammable gases, such as ammonia, methyl chloride, or propane, that could result in fatal accidents when they leaked. Thomas Midgley, Jr. created the first non-flammable, non-toxic chlorofluorocarbon gas, Freon, in 1928. The name is a trademark name owned by DuPont for any chlorofluorocarbon (CFC), hydrochlorofluorocarbon (HCFC), or hydrofluorocarbon (HFC) refrigerant. The refrigerant names include a number indicating the molecular composition (e.g., R-11, R-12, R-22, R-134A). The blend most used in direct-expansion home and building comfort cooling is an HCFC known as chlorodifluoromethane (R-22).

In the fall you should prepare your HVAC unit for winter. Turn off your air conditioner’s circuit, then hose it off to remove debris. It must dry completely. Do this when it’s warm enough that there’s no risk of the water freezing. Cover the exposed pipes with foam pipe insulation ($1-$3), and protect your entire unit with a weatherproof cover ($20-$50).
If your AC doesn’t turn off when room temperature reaches the temperature set on the thermostat, the problem is generally occurring either at the thermostat or in the electrical system that runs the outside condensing unit. You can use the AC’s circuit breaker to shut off the unit, but that should not be a permanent solution—circuit breakers are not designed to be used like light switches.
You’re constantly repairing your HVAC: If your heating and cooling system has needed repairs more than once or twice in the past few years, it may be time to take the leap with a replacement system. The money you spend repairing older equipment can often be better used towards the purchase of newer, energy-efficient HVAC systems. Here’s a simple guide: If your labor and parts cost upwards of $1,000, look toward replacement. 
In order to get the most out of your equipment, we highly recommend proper preventative HVAC maintenance. You’ll want to make sure from the outset that you have access to skilled and knowledgeable technicians who have been factory-trained to service your particular model, since different systems require different highly specific modifications. It’s advisable to find a reputable HVAC dealer in the Atlanta area that guarantees their work and offers annual service contracts to their customers to ensure necessary seasonal maintenance is always being performed regularly. Many times, timely adjustments and filter changes that are done on a regular basis can wind up saving you from breakdowns that always seem to occur right when you need your system the most.
HVAC.com has some very comprehensive resources available to aid homeowners like you in times of AC repair crisis. Using the resources below, you can work to protect your cooling system from breakdown, better understand what types of AC repairs you may face, know what to do in emergency situations, and know how to find a trusted AC repair company when you need them.

Dehumidification (air drying) in an air conditioning system is provided by the evaporator. Since the evaporator operates at a temperature below the dew point, moisture in the air condenses on the evaporator coil tubes. This moisture is collected at the bottom of the evaporator in a pan and removed by piping to a central drain or onto the ground outside.


Grand Rapids summers are nothing if hot and humid. And the last thing you want to deal with is AC repairs in the middle of that heat. The technicians at Service Professor understand the importance of keeping your air conditioner running smoothly to ensure the safety and comfort of your home and family. If your air conditioner isn’t running the way it should, your current AC is outdated or if you’re ready to install an air conditioner for the first time, you can trust Service Professor to do the job quickly, efficiently, and correctly…Guaranteed.
The first air conditioners and refrigerators employed toxic or flammable gases, such as ammonia, methyl chloride, or propane, that could result in fatal accidents when they leaked. Thomas Midgley, Jr. created the first non-flammable, non-toxic chlorofluorocarbon gas, Freon, in 1928. The name is a trademark name owned by DuPont for any chlorofluorocarbon (CFC), hydrochlorofluorocarbon (HCFC), or hydrofluorocarbon (HFC) refrigerant. The refrigerant names include a number indicating the molecular composition (e.g., R-11, R-12, R-22, R-134A). The blend most used in direct-expansion home and building comfort cooling is an HCFC known as chlorodifluoromethane (R-22).
At Reliable Comfort Heating & Air Conditioning, we combine skilled workmanship with dedicated customer service to earn your complete satisfaction.  Whether you are in need of new HVAC installation, replacement, maintenance, repair, air quality solutions, or duct sealing, we draw from extensive hands-on experience, quality products, and advanced training to maximize value and rewards.
The most recognized standards for HVAC design are based on ASHRAE data. The most general of four volumes of the ASHRAE Handbook is Fundamentals; it includes heating and cooling calculations. Each volume of the ASHRAE Handbook is updated every four years. The design professional must consult ASHRAE data for the standards of design and care as the typical building codes provide little to no information on HVAC design practices; codes such as the UMC and IMC do include much detail on installation requirements, however. Other useful reference materials include items from SMACNA, ACGIH, and technical trade journals.
Preventative Maintenance: Keep your HVAC & Refrigeration equipment operating at peak efficiency with a preventative maintenance program. Regularly maintained equipment lasts longer, provides reliable comfort on the hottest Acworth summer day, and lowers energy consumption. If you’ve ever experienced and emergency repair your know the costs are high. Components are damaged beyond repair. Let R.S. Andrews maintain your systems. Call (770) 574-6700 now.
Air duct cleaning is done by heating, ventilation and air conditioning (HVAC) professionals. The pros use industrial-strength, truck-mounted vacuums and powerful brushes and hoses to clean inside the metal ducts that make up your forced air heating and cooling system. The Environmental Protection Agency recommends duct cleaning if there is “substantial visible mold growth inside hard surface ducts, ducts that are infested with vermin such as rodents or insects, or ducts that are clogged with excessive amounts of dust and debris and/or particles are actually released into the home from your supply registers.”

HVAC.com is your one-stop shop for finding local air conditioner repair. Our free online contractor directory is home to HVAC contractor listings from across the U.S. Just type in your ZIP code to find HVAC pros in your area. You can even narrow down search results, which will help you find contractors with specific qualifications or who service certain brands.
In modern buildings, the design, installation, and control systems of these functions are integrated into one or more HVAC systems. For very small buildings, contractors normally estimate the capacity and type of system needed and then design the system, selecting the appropriate refrigerant and various components needed. For larger buildings, building service designers, mechanical engineers, or building services engineers analyze, design, and specify the HVAC systems. Specialty mechanical contractors then fabricate and commission the systems. Building permits and code-compliance inspections of the installations are normally required for all sizes of building.
The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.
Beacon Plumbing, Heating and Mechanical is a residential and commercial HVAC contractor.  We make heating and air conditioning affordable for Puget Sound area homeowners and business owners.  We are heating and cooling experts.  We are able to install, repair, service and retrofit all HVAC brands.  If your home or business needs heating, ventilation or air conditioning then we are a residential and commercial HVAC contractor that installs the most modern and advanced HVAC technology in the Seattle, WA area. 
A dehumidifier is an air-conditioner-like device that controls the humidity of a room or building. It is often employed in basements which have a higher relative humidity because of their lower temperature (and propensity for damp floors and walls). In food retailing establishments, large open chiller cabinets are highly effective at dehumidifying the internal air. Conversely, a humidifier increases the humidity of a building.

Our heater went out last Saturday, which was a cold day.  Called a few different places and they… Our heater went out last Saturday, which was a cold day.  Called a few different places and they were the only ones that called back.  The technician Tony came out and after a little testing said the main control board needed to be replaced.  He quoted us a total of $489 which seemed on the high side but it was cold and we were somewhat desperate, so we agreed and paid a parts deposit.

Before selecting the installation location of air conditioner, several main factors need to be considered. First of all, the direction of air flow from the indoor units should not fall on the place of rest or work area. Secondly, there should not be any obstacles on the way of the airflow that might prevent it from covering the space of the premises as much as possible. The outdoor unit must also be located in an open space, otherwise the heat from the house will not be effectively discharged outside and the productivity of the entire system will drop sharply. It is highly advisable to install the air conditioner units in easily accessible places, for further maintenance during operation.
When we’re in a customer’s home, we’re always on the lookout for things we can do to help them out and put a smile on their face. It could be as simple as changing a lightbulb or as involved as cleaning gutters, listing a car for sale online, or repairing a broken gate. There’s no limit to what we might do, and of course, there’s never any charge to help out. It’s good deeds for FREE!
The performance of vapor compression refrigeration cycles[23] is limited by thermodynamics. These air conditioning and heat pump devices move heat rather than convert it from one form to another, so thermal efficiencies do not appropriately describe the performance of these devices. The Coefficient-of-Performance (COP) measures performance, but this dimensionless measure has not been adopted. Instead, the Energy Efficiency Ratio (EER) has traditionally been used to characterize the performance of many HVAC systems. EER is the Energy Efficiency Ratio based on a 35 °C (95 °F) outdoor temperature. To more accurately describe the performance of air conditioning equipment over a typical cooling season a modified version of the EER, the Seasonal Energy Efficiency Ratio (SEER), or in Europe the ESEER, is used. SEER ratings are based on seasonal temperature averages instead of a constant 35 °C (95 °F) outdoor temperature. The current industry minimum SEER rating is 14 SEER.[24]
If your HVAC equipment is more than 10 years old or not keeping your house comfortable, have it evaluated by a professional HVAC contractor. If it is not performing efficiently or needs upgrading, consider replacing it with a unit that has earned the ENERGY STAR. Depending on where you live, replacing your old heating and cooling equipment with ENERGY STAR qualified equipment can cut your annual energy bill by more than $115. But before you invest in a new HVAC system, make sure that you have addressed the big air leaks in your house and the duct system. Sometimes, these are the real sources of problems rather than your HVAC equipment.
Berkeys knows how unbearable the Dallas, Plano, Fort Worth and Arlington Texas summers can be. Assuring your home’s air conditioning system is functioning properly is our job! We’ll always have the solution to your air conditioning problem, and we’ll rescue you when your system stops working. Call us or schedule your service online today and we think you will see why we are considered to be one of the Best A/C Companies in the Dallas & Fort Worth area!
As you would expect, air conditioning in Portland isn't as expensive as in most areas of the country, owing simply to the fact that most homes don't require particularly large or state-of-the-art units. While our data suggests the national average for air conditioning installation is about $6,000, in Portland we see numbers between $3,000-$4,000, although we've also seen projects as low as $1,500 and as high as $6,000. Heat pump installation is likely to be closer to the national average, but as mentioned, these devices work to be cool your home in the summer and heat in the winter.
This is a very common air conditioning problem. The unit will cool for a few hours and then it stops cooling all together. The next day or several hours later the air conditioning is cooling again but for only a few hours and then the air conditioning stops again. The reason this is happening is because the air conditioning unit is low on refrigerant because you have a refrigerant leak (the unit could freeze because of a few other air conditioning problems but this is the most common reason).
Your air conditioner’s outside unit is home to the compressor, fan, and condenser coils. These components work to release heat from the air, transferring it out of your home to produce a cool indoor climate. When the outdoor fan isn’t working correctly, the heat transfer process is hindered. Not only will this prevent your air conditioner from adequately cooling your home, a broken fan can cause the system’s compressor to overheat. An overheated compressor could trigger the air conditioner’s safety controls, turning your air conditioner off; overheating can also cause damage to the compressor itself, requiring home AC repair or compressor replacement.

    Second, there are the diagnostics involved as well as the return trip to effect the actual repair. What about the hidden costs such as having the part picked up at the supplier, was this considered? As for the parts manager at our shop having wasted time tracking the part down, it often happens that we have to contact several suppliers to find parts especially during the recent cold spell when so many suppliers were out of stock of even the most common service items due to demand being so high.
With more than 100 years in the field, Lennox has continuously offered industry-leading innovation and technology while preserving high durability and reliability standards. The professionals at Van Haaften Plumbing & Heating help bring those standards to Pella so that you can always have complete home comfort. If you’re searching for a new HVAC system or even if you just have a question about what we offer, give us a ring at 641-628-3621 or set up an appointment with us online. We’d love to hear from you. 
The use of CFC as a refrigerant was once common, including the refrigerants R-11 and R-12 (sold under the brand name Freon-12). Freon refrigerants were commonly used during the 20th century in air conditioners due to their superior stability and safety properties. When they are released accidentally or deliberately, these chlorine-bearing refrigerants eventually reach the upper atmosphere.[60] Once the refrigerant reaches the stratosphere, UV radiation from the Sun homolytically cleaves the chlorine-carbon bond, yielding a chlorine radical. These chlorine radicals catalyze the breakdown of ozone into diatomic oxygen, depleting the ozone layer that shields the Earth's surface from strong UV radiation. Each chlorine radical remains active as a catalyst until it binds with another radical, forming a stable molecule and quenching the chain reaction.
Multiple inventions within this time frame preceded the beginnings of first comfort air conditioning system, which was designed in 1902 by Alfred Wolff (Cooper, 2003) for the New York Stock Exchange, while Willis Carrier equipped the Sacketts-Wilhems Printing Company with the process AC unit the same year. Coyne College was the first school to offer HVAC training in 1899.[12]
HVAC professionals in the US can receive training through formal training institutions, where most earn associate degrees. Training for HVAC technicians includes classroom lectures and hands-on tasks, and can be followed by an apprenticeship wherein the recent graduate works alongside a professional HVAC technician for a temporary period.[29] HVAC techs who have been trained can also be certified in areas such as air conditioning, heat pumps, gas heating, and commercial refrigeration.[30]
During the coldest months of winter—even more so in Longmont—a heating system repair is probably not something you want to think about, but it likely will be if you need it on a bone-chilling day. You are lucky though, because Service Experts Heating & Air Conditioning is dedicated to completing expert quality furnace and heat pump repair, maintenance and installation in Longmont. It’s our job to be sure you are left with complete comfort in your home.
Other workers sometimes help HVACR technicians install or repair cooling and heating systems. For example, on a large air conditioning installation job, especially one in which workers are covered by union contracts, ductwork may be installed by sheet metal workers, electrical work by electricians, and pipework by plumbers, pipefitters, and steamfitters. Boiler systems are sometimes installed by a boilermaker.
Camera, Video & SurveillanceAction Cameras & Drones,Camcorders,Dash...3504 Car Electronics & GPSCar Audio,Car Mounts & Accessories,Car S...1802 Cell Phones & AccessoriesBackup Batteries,Bluetooth Devices,Cable...12628 Computers & TabletsComputer Accessories,Desktops, Monitors...5511 Musical InstrumentsAccessories,Amplifiers & Effects,Brass &...1909 Office Electronics & SuppliesNetworking,Printers & Scanners,Scanners...2201 Portable AudioBluetooth & Wireless Speakers,Docks, Rad...3233 Smart HomeCameras & Surveillance,Door Locks,Garage...104
First, it is wise to stick with a company that specializes in HVAC services. While many general handyman companies may do some things with AC units, a company that specializes in air conditioning and heating is always a better option. Because air conditioning repairs can be quite costly, depending on the particular problem, it is best to work with highly trained HVAC professionals to ensure quality work.
R22 (also known as HCFC-22) has a global warming potential about 1,800 times higher than CO2.[61] It was phased out for use in new equipment by 2010, and is to be completely discontinued by 2020. Although these gasses can be recycled when air conditioning units are disposed of, uncontrolled dumping and leaking can release gas directly into the atmosphere.

Other InformationCost to install a bathroom medicine cabinetCost to install a basement windowCost to install a bifold doorCost to install a door frameCost to install a bay windowCost to hang a prehung doorCost to install a door knobCost to install a door jambCost to install a bathtubCost to install a faucetCost to install a bidetCost to hang wallpaper
How often you should clean your air ducts depends on your situation. If you or someone in the home has asthma or is acutely allergic to certain airborne materials or pollen, regular duct cleaning may be helpful. The Environmental Protection Agency doesn’t have an official position on the necessity of air duct cleaning unless the ducts have been contaminated by rodents, insects or mold, or you are aware of particles blowing out through the vents. The EPA recommends you have your air ducts cleaned on an as-needed basis. The National Air Duct Cleaners Association (NADCA) suggests having air ducts cleaned every three to five years.
×