Denver HVAC Repair

Our technicians have experience repairing furnaces and will make sure your home is back to keeping your family cozy in no time. From training and certifications to our reputation for doing the job right time and time again, you can trust that James Heating & A/C, Inc’s furnace repair technicians will have your troubles taken care of and your furnace operating smoothly. Whether it’s emergency furnace repair or service you can schedule a little in advance, our team can give you peace of mind, knowing that your furnace is in good hands. Are you in need of a furnace repair? When performing a repair, it's important to hire professional HVAC contractors.

Replacement of air filters: dirty filters can lower your unit’s efficiency and cause damage. You can perform monthly checks and cleanings yourself. If your AC is in constant use, you’ll need to replace the filters once per month to keep the unit running properly. Filters typically cost $15-$60. Some filters are reusable, and only need regular cleaning.
Air Conditioning Service Repair - No matter what name brand (York, Trane, Carrier, Goodman, Lennox, Rheem) of air conditioning and/or heating unit you purchase some time or the other you will need to have that air conditioning and heating equipment checked for a problem and repaired. Even if you have regular air conditioning maintenance done. While there are air
Some systems include an "economizer mode", which is sometimes called a "free-cooling mode". When economizing, the control system will open (fully or partially) the outside air damper and close (fully or partially) the return air damper. This will cause fresh, outside air to be supplied to the system. When the outside air is cooler than the demanded cool air, this will allow the demand to be met without using the mechanical supply of cooling (typically chilled water or a direct expansion "DX" unit), thus saving energy. The control system can compare the temperature of the outside air vs. return air, or it can compare the enthalpy of the air, as is frequently done in climates where humidity is more of an issue. In both cases, the outside air must be less energetic than the return air for the system to enter the economizer mode.
They were quick to come out and diagnose the problem with my furnace, but I thought the estimate of $549 a bit high to replace the circuit board.  So called around and found Leo's Appliance in Concord that sells appliance parts and the circuit board was only $90.49 - that is the retail cost to me, so I imagine the wholesale cost is a lot less.  So BEWARE of this company since they wanted $500!!! to replace the circuit board which is located right in the front of the furnace - extremely easy to access.  I hate it that you cannot trust repair companies.
An air conditioning system, or a standalone air conditioner, provides cooling and humidity control for all or part of a building. Air conditioned buildings often have sealed windows, because open windows would work against the system intended to maintain constant indoor air conditions. Outside, fresh air is generally drawn into the system by a vent into the indoor heat exchanger section, creating positive air pressure. The percentage of return air made up of fresh air can usually be manipulated by adjusting the opening of this vent. Typical fresh air intake is about 10%.
Focus first on sealing ducts that run through the attic, crawlspace, unheated basement, or garage. Use duct sealant (mastic) or metal-backed (foil) tape to seal the seams and connections of ducts. After sealing the ducts in those spaces, wrap them in insulation to keep them from getting hot in the summer or cold in the winter. Next, look to seal any other ducts that you can access in the heated or cooled part of the house. See our Duct Sealing Fact Sheet (787KB) for more information.
The HVAC industry is a worldwide enterprise, with roles including operation and maintenance, system design and construction, equipment manufacturing and sales, and in education and research. The HVAC industry was historically regulated by the manufacturers of HVAC equipment, but regulating and standards organizations such as HARDI, ASHRAE, SMACNA, ACCA, Uniform Mechanical Code, International Mechanical Code, and AMCA have been established to support the industry and encourage high standards and achievement.
The federal government is phasing out Freon to conserve energy across the nation. Because of this, Freon costs are increasing significantly. If your AC unit uses Freon, eventually you’ll need to replace it to make the switch to the new R410A refrigerant. It’s most likely a good time to consider a replacement if your unit is breaking down or has problems associated with needing more Freon.
If the AC doesn’t turn off, it may be time to clean the condensing unit. Dirty condenser coils won’t give off heat efficiently and will keep the unit running.  Another possibility: The contacts on the outdoor run relay may have welded together—something that can happen over time because of frequent electrical arcing at the relay. Before checking the run relay, turn off the power to the furnace and the condensing unit. Next, disassemble the relay and pry apart the contacts. This should do the trick until you buy a replacement—which you should do soon.

Since the 1980s, manufacturers of HVAC equipment have been making an effort to make the systems they manufacture more efficient. This was originally driven by rising energy costs, and has more recently been driven by increased awareness of environmental issues. Additionally, improvements to the HVAC system efficiency can also help increase occupant health and productivity.[20] In the US, the EPA has imposed tighter restrictions over the years. There are several methods for making HVAC systems more efficient.
Believe it or not, the evaporator coils inside the AHU (Air Handling Unit) are freezing. You may notice the refrigerant lines on the condenser or at the AHU are frozen with ice build-up. The frost or ice builds up on the evaporator coils and blocks air flow (low air flow and no cooling are a sign of a low charge). A low refrigerant charge will cause the evaporator coil to operate at or below freezing. Since the coil typically operates below the dew point, it draws condensation out of the air. When the evaporator coil begins operating below freezing all this condensation freezes to the evaporator coil and the unit stops cooling.

1) Change your filter. The simplest and most effective way to keep your AC running smoothly is changing your filter once a month. By regularly changing your filter, you reduce a lot of the burden on your system. A dirty or clogged filter makes your air conditioner work much harder than does a clean filter. Changing your filters regularly is easy on your budget and easy on your system as well. It will lower your utility bill and extend the life of your AC.


Ventilation, air conditioning and heating systems require regular maintenance for them to work efficiently. You’ll likely need tune-ups and repairs for them at some point during their lifespan. However, no matter how much preventative maintenance you put into your HVAC system, there comes a time when repairs aren’t enough anymore and it’s time for a replacement.
I originally took off one star because of the SNAFU with getting the part ordered.  When Alberto called me on the phone he admitted the person had "gotten busy with other things" and apologized.  THAT was taking the high road and I was impressed by that.  Sadly, for reasons I won't guess at, Alberto has decided to take the low road in his comments and imply that they got the part as quickly as possible.  Well, we called at 2:30 so did someone spend six and a half hours finding the part??  That seems very doubtful.
HVAC pros are busy, especially in the summer. Just because you need an AC repair right now, that does not mean an HVAC pro will be available. Additionally, if they are free, your cost to repair the AC unit just went up. Emergency situations call for changes in schedules, surprise road trips and many other sudden situations. As such, air conditioning contractors tend to charge more.
An improperly maintained heating and air conditioning is an inefficient heating and air conditioning system. That’s why we provide appointments for annual inspections with our licensed technicians. It’s our goal to make sure that your home is as comfortable and energy-efficient as possible. For inspections, repairs, and service, contact BGE HOME for quality service.
Your heating and cooling equipment is vital to your comfort and breakdowns can be stressful, inconvenient and even dangerous. You can rely on the professionals at One Hour Heating and Air Conditioning* for expert service when you need it most. Our highly-trained technicians are available around the clock to meet your heating and cooling needs. We'll install, repair and maintain your HVAC system, keeping it in peak condition. Give us a call when you need to:
When signs of serious trouble arise, it is best to call a professional HVAC technician immediately. Waiting can allow the problem to worsen, which can lead to a higher repair bill. Finding a qualified technician can be as easy as asking family, friends and neighbors for recommendations or consulting online review websites and choosing a service provider that has received a significant number of positive reviews. Consumers must verify that any professional who is hired to do HVAC repair and maintenance has been properly trained and certified. Many service providers list licensing and certification information on their website.Last updated on Jul 11, 2018
A mini-split system typically supplies air conditioned and heated air to a single or a few rooms of a building.[38] Multi-zone systems are a common application of ductless systems and allow up to 8 rooms (zones) to be conditioned from a single outdoor unit. Multi-zone systems typically offer a variety of indoor unit styles including wall-mounted, ceiling-mounted, ceiling recessed, and horizontal ducted. Mini-split systems typically produce 9,000 to 36,000 Btu (9,500–38,000 kJ) per hour of cooling. Multi-zone systems provide extended cooling and heating capacity up to 60,000 Btu's.
Start with your utility company; they can help a great deal. Comparing previous bills isn't always a good measure, as the weather is never exactly the same month to month. Instead, if you take your energy bill and divide it by the square footage of livable space in your home, don't count areas like unfinished garages or basements -- you can calculate how much you are spending to heat or cool each square foot of your home. Your energy provider can tell you what the average cost per square foot is in your region for that same period of time so you can compare apples to apples.
Rapid Repair Experts proudly provide plumbing, electrical & HVAC services to Raleigh, Angier, Apex, Benson, Carrboro, Cary, Chapel Hill, Clayton, Dunn, Durham, Fuquay-Varina, Garner, Holly Springs, Knightdale, Morrisville, New Hill, Pittsboro, Rolesville, Sanford, Smithfield, Wake Forest, Wendell, Youngsville, Zebulon. If you don’t see your area, please contact us to see if we can visit you!
Outside of your home is an outdoor unit, which is called a condenser. Inside the condenser is a compressor, a condenser coil, and a large fan. The compressor pumps cool refrigerant to an evaporator coil located either in the air handler or just outside the furnace. The evaporator coil gets really cold so that when the blower or furnace pushes warm air past it, the air is cooled. This cool air is then distributed throughout your home through a series of air ducts. Heat is absorbed by the evaporator coil, which warms the refrigerant moving through the coils. This warm refrigerant is then pumped back outside to the condenser coil, where a giant fan cools it off allowing the warm air to escape. This cycle is repeated until your thermostat detects that your home has reached the temperature you set it to.
The air conditioner's evaporator coil and condenser coil collect dirt over their months and years of service. A clean filter prevents the evaporator coil from soiling quickly. In time, however, the evaporator coil will still collect dirt. This dirt reduces airflow and insulates the coil, reducing its ability to absorb heat. To avoid this problem, check your evaporator coil every year and clean it as necessary.
Each spring and fall before you start using your air conditioner, furnace, or other heating and cooling systems, you should get a tune-up to ensure your HVAC system is ready for the season. By spending a little twice a year, you can save a lot in energy bills by keeping your system operating at peak efficiency. You also can avoid costly repairs by identifying and fixing minor problems before they turn into big ones. Plus, many homeowners don't realize that their manufacturer's warranties may be considered invalid if they aren't getting their unit serviced twice a year.
Our licensed HVAC Dallas Air Conditioning technicians are experts in air conditioning, heating & cooling technology and the latest innovations in green technology, including the installation of Energy Star certified products and the use of Ozone friendly refrigerants. Residential customers depend on Berkeys for timely, quality, and affordable air conditioning repair, maintenance, and installation solutions in Dallas. Read our Air Conditioning Reviews.
Yes. You should expect to pay a diagnostic fee to cover the cost of the technician's visit, the diagnosis of your air conditioner's problem, and a quote for the repair options. You will be advised of the issue along with recommended options to correct it, which may include a system replacement if your unit is old or significantly damaged. If you decide to replace the system, the diagnostic fee will be credited toward your replacement purchase.
The compressor-based refrigerant systems are air-cooled, meaning they use air to exchange heat, in the same way as a car radiator or typical household air conditioner does. Such a system dehumidifies the air as it cools it. It collects water condensed from the cooled air and produces hot air which must be vented outside the cooled area; doing so transfers heat from the air in the cooled area to the outside air.
Brubaker Inc. is a registered Pennsylvania home improvement contractor (license #4191) and holds property and workers’ compensation insurance at levels appropriate not merely for residential work, but also for commercial and industrial projects. Brubaker Inc. is a member of the Lancaster County Code Association, the ABC Keystone Chapter, and The Lancaster Chamber of Commerce & Industry. This means you can trust that we are committed to providing the highest level of service to our community.

Never fails when you have guests! Always a plumbing issue pops up! First time I have called Bill Howe. Shower knob was frozen & we couldn't budge it. Really nice looking & polite young man named Marcus showed up promptly. He proceeded to look at problem. He explained problem & possible options if part was not easily replaceable. Fortunately the faucet was fixed with a replacement part without complications. Great news since the shower is 43 yrs. old!! Experience was very positive & I highly recommend this company!! Young repairman could not have been nicer or more professional. Will definitely recommend them.
This problem can be caused by an air-conditioning system that is too large for the house. If your system has always failed to dehumidify adequately, and it commonly short cycles (turns on and off frequently), an oversized system is ​a likely cause. An oversized system can cool the air so fast that the thermostat shuts off the system before much of the humid air has made its way across the cooling coil to get dehumidified. 
Compare replacement and repair costs: A new boiler or furnace is a substantial investment, but repair costs can also become costly as well. Not to mention, there’s always the possibility of the same issue occurring again or the need for more work in the future. You may want to replace your heating system if the repairs exceed half of the replacement costs.
Hii need you guys help! Once my thermostat drop below the set temp , my furnace does not turn on and I was wondering what’s wrong with it. It happens mostly on cold nights. Sometimes I would have to go in the basement and turned the furnace power switch off then on and will come on once I switch it off then on.i also change the thermostat recently, so I don’t think that’s the problem
Need a residential electrician in southern NH? The LeBlanc electrical team has the skilled electricians needed to resolve all of your residential and light commercial electrical needs. It's your style and your budget. We answer questions, provide estimates and install everything from lighting fixtures to whole house generators. Let us be your electrical liaison.
It’s a rare occasion for a problem to arise with your heating or cooling equipment at a convenient time. In fact, we’re not even certain such a time exists! That’s why the team at HVAC Unlimited stands ready to provide complete emergency heating and cooling repairs. No matter the time of day or the day itself, we can be on the way and ready to provide prompt, cost-efficient services to our Alexandria clients.
Copyright 2018 Rocket Lawyer Incorporated. Rocket Lawyer provides information and software only. Rocket Lawyer is not a "lawyer referral service" and does not provide legal advice or participate in any legal representation. Rocket Lawyer is not a law firm or a substitute for an attorney or law firm. Use of Rocket Lawyer is subject to our Terms of Service and Privacy Policy.
Most of the time, diagnosing problems is simple and other times it can be a complicated process where the HVAC technician calls in another HVAC technician. The technician may call in an HVAC manufacturer representative. Residential and commercial heating and cooling is important and you want the best possible HVAC air conditioning and heating service. It does not matter whether you have a Carrier Air Conditioner, Trane Air Conditioners, or need a replacement, whatever, it is best to get a qualified technician to look at your system before a decision is made to repair or replace the air conditioner or heat pump systems.
In 1902, the first modern electrical air conditioning unit was invented by Willis Carrier in Buffalo, New York.[citation needed] After graduating from Cornell University, Carrier found a job at the Buffalo Forge Company. There, he began experimenting with air conditioning as a way to solve an application problem for the Sackett-Wilhelms Lithographing and Publishing Company in Brooklyn, New York. The first air conditioner, designed and built in Buffalo by Carrier, began working on 17 July 1902.[citation needed]
Free cooling systems can have very high efficiencies, and are sometimes combined with seasonal thermal energy storage so that the cold of winter can be used for summer air conditioning. Common storage mediums are deep aquifers or a natural underground rock mass accessed via a cluster of small-diameter, heat-exchanger-equipped boreholes. Some systems with small storages are hybrids, using free cooling early in the cooling season, and later employing a heat pump to chill the circulation coming from the storage. The heat pump is added-in because the storage acts as a heat sink when the system is in cooling (as opposed to charging) mode, causing the temperature to gradually increase during the cooling season.

The condenser fan is another important HVAC element that must be maintained. Condenser fans that contain oil ports should be lubricated at least annually. The outside condenser should also be shielded from direct sunlight if possible. Keeping vegetation at least two feet away from outdoor HVAC units will also promote higher performance and potentially lower energy bills due to higher efficiency. The further away vegetation is, the better an HVAC unit will operate. 
Central home air conditioner service systems consist of two major components: a condensing unit that sits outside your house, and the evaporator coil (often referred to as an A-coil) that sits in the plenum of your furnace or air handler. The refrigerant in the A-coil picks up the heat from your home and moves it to the outdoor condensing unit. The condensing unit fan blows outside air through the condensing coil to remove the heat. The condensing unit houses the three parts replaceable by a DIYer: the contactor, the start/run capacitor(s) and the condenser fan motor. The condensing unit also houses the compressor, but only a pro can replace that. The A-coil has no parts that can be serviced by a DIYer.
×