Denver HVAC Repair

Additionally, new technology and government requirements are pushing manufacturers to build more energy efficient HVAC equipment. January 2006 we observed the end of 10 SEER units with 13 SEER air conditioning units mandated by the government. This only makes sense; however, with the higher efficiency, there comes complexity in the technology engineered into the equipment. A problem can be difficult to troubleshoot and diagnose and may require more time than the lower efficiency, less complex units.
As we all know, San Diego can get pretty warm in the summer and also quite chilly in the winter. So, in order to avoid discomfort, it is important to ensure your heating and air conditioning systems are working properly beforehand. That’s where our HVAC San Diego professionals come in. Our crew members have both the knowledge and expertise to ensure that every heating and air conditioning unit, no matter the make or model, is running at peak performance.

If you happen to live in a hot and humid area of the country, drainage problems can occur with your unit since moisture can trap itself inside the system. Routine maintenance can cut down on drainage issues by cleaning out any mold or algae from blocking the drain. If you notice moldy smells whenever you turn the thermostat down, check on your system.
BGE HOME HVAC repair technicians are thoroughly trained and certified to work on all major brands of heating and air conditioning equipment. When your system breaks down and needs a heating and air conditioning repair, you want to call someone you can trust. Need air conditioning service in the middle of the night? Emergency heating and cooling HVAC service is available 24 hours a day by calling 888-243-4663.
There is nothing worse than having your air conditioner break in the middle of a long, hot summer. You can ensure your air conditioning unit stays in working order all year long with regular service. Sometimes, however, repairs are necessary whether it’s fixing the evaporator, capacitor, or condenser or recharging the refrigerant. Most air conditioner repairs cost between $163 and $528 with most homeowners reporting that they spend about $344. If you do need a repair, here is some information to help you get it done quickly, professionally, and economically.
The customer service person on the phone was very pleasant. About an hour later a technician arrived even though it was 9pm at night. The technician seemed very experienced and thorough. He found the problem right away, but spent additional time looking over the entire system to make sure nothing else was causing other problems. He then explained the repair and gave me the price to make the repair, and asked for approval before moving ahead with the repair. The price was very reasonable, and it was repaired within an hour. I highly recommend AND Services!
Its unique feature is the presence of one main external unit that connected to several indoor units. Such systems might be the right solution for maintaining the microclimate in several offices, shops, large living spaces. Just few of outdoor units do not worsen the aesthetic appearance of the building.The main external unit can be connected to several different indoor types: floor, ceiling, cassette, etc.

I originally took off one star because of the SNAFU with getting the part ordered.  When Alberto called me on the phone he admitted the person had "gotten busy with other things" and apologized.  THAT was taking the high road and I was impressed by that.  Sadly, for reasons I won't guess at, Alberto has decided to take the low road in his comments and imply that they got the part as quickly as possible.  Well, we called at 2:30 so did someone spend six and a half hours finding the part??  That seems very doubtful.
SEER is related to the coefficient of performance (COP) commonly used in thermodynamics and also to the Energy Efficiency Ratio (EER). The EER is the efficiency rating for the equipment at a particular pair of external and internal temperatures, while SEER is calculated over a whole range of external temperatures (i.e., the temperature distribution for the geographical location of the SEER test). SEER is unusual in that it is composed of an Imperial unit divided by an SI unit. The COP is a ratio with the same metric units of energy (joules) in both the numerator and denominator. They cancel out, leaving a dimensionless quantity. Formulas for the approximate conversion between SEER and EER or COP are available.[34]
With the split system, the evaporator coil is connected to a remote condenser unit using refrigerant piping between an indoor and outdoor unit instead of ducting air directly from the outdoor unit. Indoor units with directional vents mount onto walls, suspended from ceilings, or fit into the ceiling. Other indoor units mount inside the ceiling cavity, so that short lengths of duct handle air from the indoor unit to vents or diffusers around the rooms.

Our team’s knowledge covers a variety of manufacturers, types of systems, local building codes, and best practices. Each technician goes through 200-plus hours of continuing education and training every year, including weekly training sessions. Whether your HVAC system is complex or small, old or brand new, or located in your basement or garage, our repair technicians can handle it.
Your air conditioner’s outside unit is home to the compressor, fan, and condenser coils. These components work to release heat from the air, transferring it out of your home to produce a cool indoor climate. When the outdoor fan isn’t working correctly, the heat transfer process is hindered. Not only will this prevent your air conditioner from adequately cooling your home, a broken fan can cause the system’s compressor to overheat. An overheated compressor could trigger the air conditioner’s safety controls, turning your air conditioner off; overheating can also cause damage to the compressor itself, requiring home AC repair or compressor replacement.

Advantages of the ductless system include smaller size and flexibility for zoning or heating and cooling individual rooms. The inside wall space required is significantly reduced. Also, the compressor and heat exchanger can be located farther away from the inside space, rather than merely on the other side of the same unit as in a PTAC or window air conditioner. Flexible exterior hoses lead from the outside unit to the interior one(s); these are often enclosed with metal to look like common drainpipes from the roof. In addition, ductless systems offer higher efficiency, reaching above 30 SEER.[39]

The heat-exchanger cools the air that is being forced through it by the furnace blower. As the warm air comes in contact with this cool surface the water in the air condenses. By pulling the water molecules from the air. According to the psychometric chart[42] as relative humidity decreases in order to feel cool you will have to lower the temperature even more. A common way to counteract this effect is by installing a whole-home humidifier.[43] Similarly, installing a high efficient system this need to turn the temperature down wont have such and influence on your energy costs.
Just like running a marathon, we perform better at full strength. If we’re not feeling great, it’s that much harder to finish the race. Similarly, when you set your thermostat to a certain temperature, the system is tasked with maintaining that temperature throughout the room. Working at full strength, the system can easily maintain that temperature (as long as it’s not below 60 degrees or above 80 degrees). However, when injured, the system may struggle to keep the room at your desired temperature. As such, it’s working harder, which means higher utility bills.
Reinstall the access panel and disconnect block. Turn on the circuit breaker and furnace switch. Then set the thermostat to a lower temperature and wait for the AC to start (see “Be Patient at Startup,” below). The compressor should run and the condenser fan should spin. If the compressor starts but the fan doesn’t, the fan motor is most likely shot. Shut off the power and remove the screws around the condenser cover. Lift the cover and remove the fan blade and motor (photo 7). Reinstall the blade and secure the cover. Then repower the unit and see if the fan starts. If it doesn’t, you’ve given it your best shot—it’s time to call a pro.
×