Denver HVAC Repair

We do our best to screen all of our hvac contractors. However, there are still some hvac contractor professionals in Portland that have not been pre-screened. This means that their licenses may not be up to date to operate in Portland or OR. Always be sure to pre-screen them yourself before hiring. Here are some unscreened professionals offering hvac:

Here’s a simple test to try on your own: When it’s hotter than 80 degrees outside, turn on your AC unit, and set it to well below room temperature. Let it run for 15 minutes, then use a thermometer to check just outside the return duct (the area where air flows in to be cooled). Now take a temperature reading just outside the strongest, most easily accessible vent (where cool air should be flowing out). Subtract the second reading from the first. If the difference between these two is fewer than 14 degrees, your HVAC unit might need work. 


Air conditioning units work by using evaporator and condenser coils to remove heat from the air in your home. Warm household air blows through the evaporator coils, which transfer the heat into refrigerant vapor, which is then moved to the condenser in the outdoor part of the unit. The condenser coils turn the now-warm refrigerant vapor into liquid, allowing the heat to be dispersed outside and away from your home.
a/c compressor needed replacing. the A Team Mechanical found a way to return the next day to complete the repairs and made sure the system was running effectively. Even put down another concrete base pad to level the a/c unit. They were professionals and straight forward with the services needed. All the other HVAC companies wanted to charge me three time the amount for the services.
Fast forward 1 year and 1 week and the circuit board that HVAC Service had installed has failed again. They came out and said that it failed from water condensation dripping onto it, so we needed to replace it and reroute the pipes to prevent future water damage.  That would cost double what I paid last year.  Why didn't they fix the problem last year at the initial repair instead of putting in a circuit board that was bound to fail again?!? They were strongly recommending that the furnace be completely replace for a huge fee to avoid the same thing happening again.  I paid $59 for them to tell me they didn't fix it right last year. This didn't feel right, so I sought a second opinion.
1) Change your filter. The simplest and most effective way to keep your AC running smoothly is changing your filter once a month. By regularly changing your filter, you reduce a lot of the burden on your system. A dirty or clogged filter makes your air conditioner work much harder than does a clean filter. Changing your filters regularly is easy on your budget and easy on your system as well. It will lower your utility bill and extend the life of your AC.
Modern air conditioning systems are not designed to draw air into the room from the outside, they only recirculate the increasingly cool air on the inside. Because this inside air always has some amount of moisture suspended in it, the cooling portion of the process always causes ambient warm water vapor to condense on the cooling coils and to drip from them down onto a catch tray at the bottom of the unit from which it must then be routed outside, usually through a drain hole. As this moisture has no dissolved minerals in it, it will not cause mineral buildup on the coils. This will happen even if the ambient humidity level is low. If ice begins to form on the evaporative fins, it will reduce circulation efficiency and cause the development of more ice, etc. A clean and strong circulatory fan can help prevent this, as will raising the target cool temperature of the unit's thermostat to a point that the compressor is allowed to turn off occasionally. A failing thermistor may also cause this problem. Refrigerators without a defrost cycle may have this same issue. Dust can also cause the fins to begin blocking air flow with the same undesirable result: ice.
Abacus’ residential and commercial plumbers are proficient at repairing all kinds of plumbing issues, including gas and electric water heaters, slab leaks, leaky pipes to hydro jetting clogged drains. Many plumbing problems are not DIY types of jobs, call Abacus so one of our licensed plumbers can fix your problem. Our plumbers are not only knowledgeable but their customer service skills will meet or exceed your expectations.
With colder weather on its way back to Waldorf, furnace and heating repair may not be the first thing you think about, but maybe it should be. Sure, it’s easy for us to sit here and tell you to schedule annual furnace service, but it’s only because we want to help you avoid a heating breakdown during the coldest day of the month in Waldorf. Day or night, our HVAC experts are here to make sure you have a comfortable home, and can help get your furnace back running in little time.

At R&R Heating & Air Conditioning, we’re proud of our reputation built on honesty, quality and service. Our family-owned and operated company has been serving Orland Park, Tinley Park, Palos, Oak Lawn and surrounding communities since 1986. Our goal is to help you create and maintain a healthy indoor climate in your home or commercial building. Using our high-efficiency HVAC systems, you’ll use less energy, cut down on utility costs and live and work in comfortable interior spaces year-round.
The heat pump gained popularity in the 1950s in Japan and the United States.[13] Heat pumps can extract heat from various sources, such as environmental air, exhaust air from a building, or from the ground. Initially, heat pump HVAC systems were only used in moderate climates, but with improvements in low temperature operation and reduced loads due to more efficient homes, they are increasing in popularity in cooler climates.
Replacing a capacitor is easy. Just take a photo of the wires before disconnecting anything (you may need a reference later on). Then discharge the stored energy in the old capacitor (Photo 4). Use needle-nose pliers to pluck one wire at a time from the old capacitor and snap it onto the corresponding tab of the new capacitor. The female crimp connectors should snap tightly onto the capacitor tabs. Wiggle each connector to see if it’s tight. If it’s not, remove the connector and bend the rounded edges of it so it makes a tighter fit on the tab. When you’ve swapped all the wires, secure the new capacitor (Photo 5).
×