Denver HVAC Repair

If your air ducts have been damaged, you’ll need to replace them. The national average air duct replacement cost is $150-$280, which may not include materials. Factors such as duct material, labor, location of ducts and linear feet of ductwork will all affect your final costs. Labor costs will vary based on how accessible the ducts are and what material your ducts are made of. The least expensive duct material is a flexible, non-metallic ducting that costs approximately $1-$2 per linear foot. Flexible aluminum is generally more expensive and stronger than non-metallic ducting. Stainless steel ducting is the strongest, the least flexible (meaning installing it typically has higher labor rates), and usually the most expensive. An average price for air duct replacement could range between $35 and $55 per linear foot, including basic materials and labor. A typical single-family home has 6-10 duct runs; replacing or installing one duct run could average $150-$250 for labor.
This time we had a major issue with our sewage line related to roots. Was terrible. But we called Billy Howe and Mike came and did an Incredible job. Not only he explained really well what was going on but he was careful and knowledgeable. I was so relief that not only we trust in BH team but we were lucky that was Mike coming to execute the service.
During a seasonal tune-up, our technicians run diagnostics on every part of your system. We make sure the fans run smoothly, the thermostat is programed to your liking, and that all critical parts are not showing signs of wear. If a component needs replacing, we will replace it for you before it gives out. We’ll even replace the filter for you – one less hassle!
At Van Haaften Plumbing & Heating, heating and cooling isn’t just our job, it’s our passion. We’re dedicated to providing you with the top HVAC service in Pella. No matter the size of the problem or time of day, you can rely on us to get the job done properly. After all, Van Haaften Plumbing & Heating has been serving the community since 1949, bringing comfort to our customers in every season.
The content of this blog is intended for informational purposes only. Renovate America provides no endorsement and makes no representations as to accuracy, reliability, completeness, suitability or validity of any information or content on, distributed through or linked, downloaded or accessed from this site. This blog is subject to the additional terms found at https://www.renovateamerica.com/blog-disclaimer.

The Refrigeration Loop is a closed system and refrigerant should never have to be added to the unit unless there is a leak. Most residential units use R-22/R410A refrigerant. Prices of R-22/R410A are rising every year as we get closer to the date when refrigerant manufacturers will no longer be able to make R-22/R410A. Phase-out of R-22, an HCFC, begins in 2010 and expected to be complete by 2020.). Furthermore, make sure you ask what the service company charges for R-22 when you are calling an HVAC contractor.
Ground source, or geothermal, heat pumps are similar to ordinary heat pumps, but instead of transferring heat to or from outside air, they rely on the stable, even temperature of the earth to provide heating and air conditioning. Many regions experience seasonal temperature extremes, which would require large-capacity heating and cooling equipment to heat or cool buildings. For example, a conventional heat pump system used to heat a building in Montana's −70 °F (−57 °C) low temperature or cool a building in the highest temperature ever recorded in the US—134 °F (57 °C) in Death Valley, California, in 1913 would require a large amount of energy due to the extreme difference between inside and outside air temperatures. A few feet below the earth's surface, however, the ground remains at a relatively constant temperature. Utilizing this large source of relatively moderate temperature earth, a heating or cooling system's capacity can often be significantly reduced. Although ground temperatures vary according to latitude, at 6 feet (1.8 m) underground, temperatures generally only range from 45 to 75 °F (7 to 24 °C).
Eventually, every homeowner experiences a malfunction in their heating unit. It’s a cold morning and you hike the thermostat up like you usually do to take the chill off, but you get no response. You don’t hear the system firing up or feel the radiators or air vents producing any heat. You hope it’s just a quick fix, like a clogged filter or a tripped circuit breaker. On the other hand, you might be wondering if it’s more cost-effective to just have the unit replaced.
Hospital operating theatres, in which air is filtered to high levels to reduce infection risk and the humidity controlled to limit patient dehydration. Although temperatures are often in the comfort range, some specialist procedures, such as open heart surgery, require low temperatures (about 18 °C, 64 °F) and others, such as neonatal, relatively high temperatures (about 28 °C, 82 °F).
Should I repair or replace my HVAC? It’s a common question — and you need to weigh several factors to make the decision. One of the most significant factors is the lifespan of your unit. According to EnergyStar — a U.S. Environmental Protection Agency voluntary program — an A.C. unit lasts about 15 to 20 years. On average, a heat pump perseveres for 16 years and a furnace functions for between 15 to 20 years, reports This Old House.
To be honest, an HVAC technician’s work goes beyond more than installation, maintenance and repair. Most people are increasingly spending more time inside the home, so indoor air quality, home energy savings and total comfort have become even more important. There are several choices and solutions when it comes to HVAC systems, and our experts will consult with you every step of the way and work with you to achieve your goals.
×