Monday the following week, no phone calls, or follow up. I call to get an update and am told that they cannot install my system because they don't have time. I ask what does that mean, one year? One week? Until the end of summer they say. What does that mean I ask? They say at the end of September. I say thank you for wasting 1 month of my time.
The customer service person on the phone was very pleasant. About an hour later a technician arrived even though it was 9pm at night. The technician seemed very experienced and thorough. He found the problem right away, but spent additional time looking over the entire system to make sure nothing else was causing other problems. He then explained the repair and gave me the price to make the repair, and asked for approval before moving ahead with the repair. The price was very reasonable, and it was repaired within an hour. I highly recommend AND Services!
Regardless of how far along you are in your air conditioning project, you should start looking for a contractor now. The demand for Portland air conditioning has begun to outstrip the supply of contractors, and homeowners are telling us they've had to fight/wait to schedule an installation date. This may also determine the availability of your preferred contractor, as the best contractors' schedules tend to fill more quickly than the rest. Once you've submitted your online request, you can trust that our contractors are the most reliable professionals in the business. Each and every one our contractors has been put through a rigorous ten-step screening process. Our online customer ratings and reviews section will allow you to see what other homeowners have said, not just about individual contractors, but Portland air conditioning installation in general.
The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.
Air conditioner equipment power in the U.S. is often described in terms of "tons of refrigeration", with each approximately equal to the cooling power of one short ton (2000 pounds or 907 kilograms) of ice melting in a 24-hour period. The value is defined as 12,000 BTU per hour, or 3517 watts. Residential central air systems are usually from 1 to 5 tons (3.5 to 18 kW) in capacity.
Check your filter every month, especially during heavy use months (winter and summer). If the filter looks dirty after a month, change it. At a minimum, change the filter every 3 months. A dirty filter will slow down air flow and make the system work harder to keep you warm or cool — wasting energy. A clean filter will also prevent dust and dirt from building up in the system — leading to expensive maintenance and/or early system failure.
When your heating or cooling system finally breaks, it’s not usually during convenient office hours or in mild weather. Your HVAC unit has to work harder during extreme conditions like a sweltering summer day or freezing winter night, so it is much more likely to fail during those times. R.S. Andrews has our customers’ safety and comfort as our priority, so we offer service 24 hours a day for emergencies. No matter when your equipment fails, you can count on us to repair it quickly and efficiently!
In modern buildings, the design, installation, and control systems of these functions are integrated into one or more HVAC systems. For very small buildings, contractors normally estimate the capacity and type of system needed and then design the system, selecting the appropriate refrigerant and various components needed. For larger buildings, building service designers, mechanical engineers, or building services engineers analyze, design, and specify the HVAC systems. Specialty mechanical contractors then fabricate and commission the systems. Building permits and code-compliance inspections of the installations are normally required for all sizes of building.
In 1758, Benjamin Franklin and John Hadley, a chemistry professor at Cambridge University, conducted an experiment to explore the principle of evaporation as a means to rapidly cool an object. Franklin and Hadley confirmed that evaporation of highly volatile liquids (such as alcohol and ether) could be used to drive down the temperature of an object past the freezing point of water. They conducted their experiment with the bulb of a mercury thermometer as their object and with a bellows used to speed up the evaporation. They lowered the temperature of the thermometer bulb down to −14 °C (7 °F) while the ambient temperature was 18 °C (64 °F). Franklin noted that, soon after they passed the freezing point of water 0 °C (32 °F), a thin film of ice formed on the surface of the thermometer's bulb and that the ice mass was about 6 mm (1⁄4 in) thick when they stopped the experiment upon reaching −14 °C (7 °F). Franklin concluded: "From this experiment one may see the possibility of freezing a man to death on a warm summer's day."
For every job, our level of professionalism, courteous treatment, and job site management sets us apart. You’ll get the information and recommendations you need to make smart decisions, and enjoy the results that increase the value of your HVAC equipment. Let us simplify your temperature control requirements with prompt response, quick turnaround, and turnkey solutions. Two Waynes … No waiting!
Central home air conditioner service systems consist of two major components: a condensing unit that sits outside your house, and the evaporator coil (often referred to as an A-coil) that sits in the plenum of your furnace or air handler. The refrigerant in the A-coil picks up the heat from your home and moves it to the outdoor condensing unit. The condensing unit fan blows outside air through the condensing coil to remove the heat. The condensing unit houses the three parts replaceable by a DIYer: the contactor, the start/run capacitor(s) and the condenser fan motor. The condensing unit also houses the compressor, but only a pro can replace that. The A-coil has no parts that can be serviced by a DIYer.