Denver HVAC Repair

The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.
If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
We will get into specifics later, but there are plenty of recommended maintenance items all homeowners should strongly consider if you want you to extend the lifespan of your AC unit. Furthermore, regular maintenance prevents certain repairs less organized homeowners see every few years. Some easy and highly recommended AC unit maintenance tasks include:
We’re located in Lexington and service the surrounding area, so stop on by if you’re looking for a new furnace or want to set up an appointment to have one of our techs do a consultation at your home and help you figure out which system is ideal for your home. Schedule furnace repair or a furnace service appointment with James Heating & A/C, Inc using our online scheduler, or if you need help more quickly, give us a buzz at 336-853-6070. 
Abacus’ plumbers are also experts at sewer & pipe repairs, shower & tub repairs/installations, kitchen & bath faucet repair/installations, sink repairs/installation, plumbing inspections, water filtration, water softening, garbage disposal repair/installation, toilet repair/replacement, drain cleaning with drain camera inspections, leak detection/repair, plumbing repair/installation and back flow prevention for all Houston Texas homes & commercial business properties. Need an annual Plumbing Inspection on all your home’s plumbing systems? Ask about the Abacus CLUB. The CLUB membership will give you the peace of mind that your plumbing system is working at top efficiency. Our licensed plumbers will conduct an inspection of your home to look for and fix any potential plumbing problems. 
Are there watermarks on your ceiling? Visible leaks around your outdoor unit? Has your AC system completely stopped working? If you notice any of these signs, it’s in your best interest to call an AC technician to fix the issue before it causes more problems for you, your AC system, and your home. To learn more about potential AC malfunctions and how we fix AC issues, visit our AC Repair page.
New heating and cooling equipment installations present a wide variety of options that can save you money on your power bills and reduce the amount of HVAC maintenance and service that will ultimately be required over the life of your new unit. Energy-efficient options like heat pumps, two-stage furnaces, air-to-heat exchangers (HRVs), and programmable thermostats can all go a long way toward increasing efficiency and extending the life expectancy of your system.
“Robinson Air = top notch professionals. Mike was personable, knowledgeable, timely, thorough, and left me with a hard copy of prioritized recommendations and his explanations of HVAC needs I may have in the future. I was very impressed with being shown a tablet picture of a possible problem. It was so refreshing to have the service and all phone interactions handled so well and smoothly…thank you for taking the “angst” out of this kind of service call. My hat is off to you and I will happily recommend you to family and friends. Thank you!!!”
Before selecting the installation location of air conditioner, several main factors need to be considered. First of all, the direction of air flow from the indoor units should not fall on the place of rest or work area. Secondly, there should not be any obstacles on the way of the airflow that might prevent it from covering the space of the premises as much as possible. The outdoor unit must also be located in an open space, otherwise the heat from the house will not be effectively discharged outside and the productivity of the entire system will drop sharply. It is highly advisable to install the air conditioner units in easily accessible places, for further maintenance during operation.
When your heating or cooling system finally breaks, it’s not usually during convenient office hours or in mild weather. Your HVAC unit has to work harder during extreme conditions like a sweltering summer day or freezing winter night, so it is much more likely to fail during those times. R.S. Andrews has our customers’ safety and comfort as our priority, so we offer service 24 hours a day for emergencies. No matter when your equipment fails, you can count on us to repair it quickly and efficiently!

The quality of the air you breathe affects your comfort, health, and productivity.  Whether at home or in the workplace, an ample supply of fresh, clean air is essential to everyday life.  Whatever concerns you may face, Edwards Heating & Air provides proven, cost-effective products to significantly improve Indoor Air Quality.  Our NATE-certified specialists are qualified to analyze your residential or commercial space, make informed recommendations, and implement a strategy specifically targeted at your unique circumstances.  As a Carrier Factory Authorized Dealer, we are extensively trained in leading-edge products that silently and effectively eliminate harmful bacteria, fumes, chemicals, viruses, smoke, and much more.  The installation of a humidifier, ventilator, air filter, or UV lamp will protect the health of your indoor breathing air, maintain a cleaner, more comfortable home, and even reduce energy costs.  Contact the specialists from Edwards Heating & Air for trusted solutions and complete peace of mind.  

The use of furnaces, space heaters, and boilers as a method of indoor heating could result in incomplete combustion and the emission of carbon monoxide, nitrogen oxides, formaldehyde, volatile organic compounds, and other combustion byproducts. Incomplete combustion occurs when there is insufficient oxygen; the inputs are fuels containing various contaminants and the outputs are harmful byproducts, most dangerously carbon monoxide, which is a tasteless and odorless gas with serious adverse health effects.[14]
Need 24-hour emergency furnace repair? We can handle that too. With our same-day service and live phone and online chat service available 24/7, we make your comfort our greatest priority. Heating and air conditioning should help you live a comfortable life, so let us help you make your home the most comfortable it has ever been. It’s easy, just grab your furnace repair coupon, then simply give us a call at 208-488-4892, chat or schedule an appointment with us online.
Technician Laurence arrived on time. I was running 20 minutes late and he waited patiently for my arrival. I described the problem with my air conditioner. He examined the A/C system and quickly diagnosed the problem. He had identified that the capacitor was not functioning and replaced it. Her then started the A/C system and confirmed that it was working well. He also checked refrigerant level. I am very happy with the service provided and the professionalism of Bill Howe Technician Laurence. I would highly recommend Bill Howe Heating & Air.
Other than mineral deposits, the most common problem is sediment in the water supply. The float inlet valve has a tiny hole that easily clogs. The float is usually made of plastic, and if cracked will fill with water and sink. The valve will be stuck open and the reservoir will overflow. Use caution when scraping deposits off the float. If the deposits cannot be removed, replace the float or it will sink and cause an overflow.

The condenser fan is another important HVAC element that must be maintained. Condenser fans that contain oil ports should be lubricated at least annually. The outside condenser should also be shielded from direct sunlight if possible. Keeping vegetation at least two feet away from outdoor HVAC units will also promote higher performance and potentially lower energy bills due to higher efficiency. The further away vegetation is, the better an HVAC unit will operate. 


As an Atlanta resident, you’re well aware that the weather in our area can go through extremes of both hot and cold throughout the year, taxing your heating and cooling system to its limits. You’ll likely encounter the need for repair or replacement at some point. If you need HVAC installation, HVAC maintenance, or HVAC service and repair, R.S. Andrews is the most trusted name in Atlanta.
The selection of indoor units has one restriction - their total power should not exceed the capacity of the outdoor unit. In practice, however, it is very common to see a multi-split system with a total capacity of indoor units greater than the outdoor capacity by at least 20%. However, it is wrong to expect better performance when all indoor units are turned on at the same time, since the total capacity of the whole system is limited by the capacity of the outdoor unit. Simply put, the outdoor unit will distribute all its power to all operating indoor units in such a way that some of the rooms may not have a very comfortable temperature level. However, the calculation of the total power is not simple, since it takes into account not only the nominal power of the units, but also the cooling capacity, heating, dehumidification, humidification, venting, etc.
Should you need to replace an air conditioning unit, Abacus Plumbing recommends Lennox brand of air conditioning and heating systems. Lennox systems offer the highest level of home comfort at the lowest possible cost of operation. Additionally, these systems are praised by consumer publications and meet or exceed all government standards for efficiency. Learn more about installation »
Monday the following week, no phone calls, or follow up.  I call to get an update and am told that they cannot install my system because they don't have time.  I ask what does that mean, one year? One week? Until the end of summer they say.  What does that mean I ask?  They say at the end of September.  I say thank you for wasting 1 month of my time.
"Our Pro was the most courteous and informative gentleman that we have had the pleasure to work with, was great. He let us know immediately what the problem was and what the cost to fix it would be. Also, he let us know how to maintain and extend the life of our washer. He was very personable and made us very comfortable with the process. We would have him back in a heartbeat if anything ever goes wrong again. It was the best experience we have ever had with a appliance repair service."
When your heating or cooling system finally breaks, it’s not usually during convenient office hours or in mild weather. Your HVAC unit has to work harder during extreme conditions like a sweltering summer day or freezing winter night, so it is much more likely to fail during those times. R.S. Andrews has our customers’ safety and comfort as our priority, so we offer service 24 hours a day for emergencies. No matter when your equipment fails, you can count on us to repair it quickly and efficiently!
Beacon Plumbing, Heating and Mechanical is a residential and commercial HVAC contractor.  We make heating and air conditioning affordable for Puget Sound area homeowners and business owners.  We are heating and cooling experts.  We are able to install, repair, service and retrofit all HVAC brands.  If your home or business needs heating, ventilation or air conditioning then we are a residential and commercial HVAC contractor that installs the most modern and advanced HVAC technology in the Seattle, WA area. 
Some systems include an "economizer mode", which is sometimes called a "free-cooling mode". When economizing, the control system will open (fully or partially) the outside air damper and close (fully or partially) the return air damper. This will cause fresh, outside air to be supplied to the system. When the outside air is cooler than the demanded cool air, this will allow the demand to be met without using the mechanical supply of cooling (typically chilled water or a direct expansion "DX" unit), thus saving energy. The control system can compare the temperature of the outside air vs. return air, or it can compare the enthalpy of the air, as is frequently done in climates where humidity is more of an issue. In both cases, the outside air must be less energetic than the return air for the system to enter the economizer mode.
Air conditioners improperly installed will develop air duct leaks and low air flow. Your air conditioner looses its cooling power in hot weather. A lack of maintenance will cause your air conditioner to malfunction. Refrigerant charges and compressors are some of the parts needing regular maintenance. Regular maintenance increases the lifespan and production of your air conditioner.
With the split system, the evaporator coil is connected to a remote condenser unit using refrigerant piping between an indoor and outdoor unit instead of ducting air directly from the outdoor unit. Indoor units with directional vents mount onto walls, suspended from ceilings, or fit into the ceiling. Other indoor units mount inside the ceiling cavity, so that short lengths of duct handle air from the indoor unit to vents or diffusers around the rooms.
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
In modern buildings, the design, installation, and control systems of these functions are integrated into one or more HVAC systems. For very small buildings, contractors normally estimate the capacity and type of system needed and then design the system, selecting the appropriate refrigerant and various components needed. For larger buildings, building service designers, mechanical engineers, or building services engineers analyze, design, and specify the HVAC systems. Specialty mechanical contractors then fabricate and commission the systems. Building permits and code-compliance inspections of the installations are normally required for all sizes of building.
ArtCanvas,Framed Art,Mixed Media,Photograph...32162 BathBath Accessories & Sets,Bath Rugs,Bath S...3961 BeddingBed Pillows,Blankets & Throws,Comforter...4144 Floor Care & CleaningBrooms, Mops & Dusters,Vacuums1059 FurnitureAccent Furniture,Baby & Kid's Furniture...8941 Heating, Cooling & Air QualityAir Conditioners,Air Purifiers,Dehumidif...1387 Home AppliancesIrons & Garment Care,Sewing Machines,Sma...4121 Home DecorCandles & Holders,Home Accents,Lamps & L...13870
Circulating refrigerant vapor enters the compressor, where its pressure and temperature are increased. The hot, compressed refrigerant vapor is now at a temperature and pressure at which it can be condensed and is routed through a condenser. Here it is cooled by air flowing across the condenser coils and condensed into a liquid. Thus, the circulating refrigerant removes heat from the system and the heat is carried away by the air. The removal of this heat can be greatly augmented by pouring water over the condenser coils, making it much cooler when it hits the expansion valve.
Before selecting the installation location of air conditioner, several main factors need to be considered. First of all, the direction of air flow from the indoor units should not fall on the place of rest or work area. Secondly, there should not be any obstacles on the way of the airflow that might prevent it from covering the space of the premises as much as possible. The outdoor unit must also be located in an open space, otherwise the heat from the house will not be effectively discharged outside and the productivity of the entire system will drop sharply. It is highly advisable to install the air conditioner units in easily accessible places, for further maintenance during operation.
We service and install forced air systems from all manufacturers, including Trane, Burnham, Heil, Rheem, and many more. If your home needs a new system, we will recommend the best system for your needs and budget. If you have a brand preference, we can recommend and provide qualified installation of a system from that company that fits your home’s needs.
Air conditioner equipment power in the U.S. is often described in terms of "tons of refrigeration", with each approximately equal to the cooling power of one short ton (2000 pounds or 907 kilograms) of ice melting in a 24-hour period. The value is defined as 12,000 BTU per hour, or 3517 watts.[32] Residential central air systems are usually from 1 to 5 tons (3.5 to 18 kW) in capacity.

You should also have air ducts cleaned after recent water contamination or water damage to prevent mold; after renovations or remodeling to ensure debris and dust didn’t settle in the vents and ducts; if you are having problems with allergies or asthma; or when you are moving into a newly purchased home, especially if the previous owners smoked or had pets. The National Air Duct Cleaners Association (NADCA) recommends getting your air ducts cleaned every three to five years, or every two to three years in regions where homeowners use their air conditioning and heater for many months of the year, while the EPA suggests homeowners have duct cleaning done as needed.


AutomotiveCar Care,Car Electronics,Car Safety & Se...8511 ElectricalBatteries,Extension Cords & Power Strips...2333 Fire Pits & Outdoor Heaters151 Grills & AccessoriesGrill Covers,Grilling Accessories,Grills...775 Hand & Power ToolsHand Tools,Power Tool Accessories,Power...6450 Heating & CoolingAir Conditioners,Dehumidifiers,Draft Sto...1557 Home ImprovementAppliances,Bathroom Faucets,Building Mat...10774 LightingCeiling Fans,Fixtures,Flood Lights & Sec...2657
“We had a great experience with Robinson’s! The office staff, then the gentleman who helped me with questions over the phone and Kyle, our service tech, were all great and very easy to work with. They gave me a time frame for when to expect Kyle the same day. A phone call to let me know he was on his way. A text with picture so I knew who to be expecting. Kyle arrived on time and was very knowledgeable and friendly. He did a great job. You could tell he liked his job. Prices were reasonable. We will be using and recommending Robinson’s Air – Wichita Falls in the future.”
Fast forward 1 year and 1 week and the circuit board that HVAC Service had installed has failed again. They came out and said that it failed from water condensation dripping onto it, so we needed to replace it and reroute the pipes to prevent future water damage.  That would cost double what I paid last year.  Why didn't they fix the problem last year at the initial repair instead of putting in a circuit board that was bound to fail again?!? They were strongly recommending that the furnace be completely replace for a huge fee to avoid the same thing happening again.  I paid $59 for them to tell me they didn't fix it right last year. This didn't feel right, so I sought a second opinion.
Each spring and fall before you start using your air conditioner, furnace, or other heating and cooling systems, you should get a tune-up to ensure your HVAC system is ready for the season. By spending a little twice a year, you can save a lot in energy bills by keeping your system operating at peak efficiency. You also can avoid costly repairs by identifying and fixing minor problems before they turn into big ones. Plus, many homeowners don't realize that their manufacturer's warranties may be considered invalid if they aren't getting their unit serviced twice a year.

Change the filter: A new filter can cost as little as $20. Since this is the most effective way of maintaining your AC system, there is no reason not to change your filter. Homeowners should change your AC filters whenever it gets dirty. Depending on the filter, you may have to change it once every six months or once every month. Each filter should indicate how long it will last.
Your HVAC professional can perform a yearly tune-up of your system for around $80-$100. This yearly maintenance can go far toward heading off major repairs to your system, and provide you with peace of mind and considerable savings in the long term. Additionally, regular servicing of your AC unit can help a home inspector to certify that your unit is working properly in the event you decide to sell your home.
We were following up on this review and the service call we did for you. We could not find you in our system of ever having gone out to your home. If you could please provide us with the date we were out and the name under which the call was placed that would be great as we would like to see if there is any way we can rectify the situation. We do offer a 100% Satisfaction Guarantee, we have tried to private message you to no avail. Can you please call us at 925-318-4795?  
Our heater went out last Saturday, which was a cold day.  Called a few different places and they… Our heater went out last Saturday, which was a cold day.  Called a few different places and they were the only ones that called back.  The technician Tony came out and after a little testing said the main control board needed to be replaced.  He quoted us a total of $489 which seemed on the high side but it was cold and we were somewhat desperate, so we agreed and paid a parts deposit.
The HVAC industry is a worldwide enterprise, with roles including operation and maintenance, system design and construction, equipment manufacturing and sales, and in education and research. The HVAC industry was historically regulated by the manufacturers of HVAC equipment, but regulating and standards organizations such as HARDI, ASHRAE, SMACNA, ACCA, Uniform Mechanical Code, International Mechanical Code, and AMCA have been established to support the industry and encourage high standards and achievement.
In the UK, the Ozone Regulations[62] came into force in 2000 and banned the use of ozone depleting HCFC refrigerants such as R22 in new systems. The Regulation banned the use of R22 as a "top-up" fluid for maintenance between 2010 (for virgin fluid) and 2015 (for recycled fluid). This means that equipment that uses R22 can still operate, as long as it does not leak. Although R22 is now banned, units that use the refrigerant can still be serviced and maintained.
The heat-exchanger cools the air that is being forced through it by the furnace blower. As the warm air comes in contact with this cool surface the water in the air condenses. By pulling the water molecules from the air. According to the psychometric chart[42] as relative humidity decreases in order to feel cool you will have to lower the temperature even more. A common way to counteract this effect is by installing a whole-home humidifier.[43] Similarly, installing a high efficient system this need to turn the temperature down wont have such and influence on your energy costs.
Window unit air conditioners are installed in an open window. The interior air is cooled as a fan blows it over the evaporator. On the exterior the heat drawn from the interior is dissipated into the environment as a second fan blows outside air over the condenser. A large house or building may have several such units, allowing each room to be cooled separately.

Our company has been serving Woodbridge and the Northern Virginia region since 1979. We don’t compromise on quality — our team members pride themselves on providing the top-quality service each and every time. We attribute our success to the fact that we’re responsive to our customers’ needs, no matter if they’re residential or commercial, large or small. Whether you need routine maintenance or a complete system installation, our team of trained technicians is at your beck and call, and we’re prepared to deliver quality services and products at an affordable price. We live by the time-tested motto, “Do the job right the first time.”

In the UK, the Ozone Regulations[62] came into force in 2000 and banned the use of ozone depleting HCFC refrigerants such as R22 in new systems. The Regulation banned the use of R22 as a "top-up" fluid for maintenance between 2010 (for virgin fluid) and 2015 (for recycled fluid). This means that equipment that uses R22 can still operate, as long as it does not leak. Although R22 is now banned, units that use the refrigerant can still be serviced and maintained.


You can keep your air conditioner running efficiently with some preventative care measures. Shut off the power to your AC before cleaning it or performing any of these tasks:  clean your filter at least twice a year; remove leaves and twigs from cages; clean the fins with a garden hose or special spray, then use a butter knife to straighten any that are crooked; keep your yard clean so the fins won't get blocked; cover the unit up for winter; and make sure it's level or you run the risk of damaging the inner workings of the unit.
"Friendly, professional, responded quickly to my problem. I have called many air conditioning companies about my problem including the maker of the unit and had come to the conclusion that I would not find someone to repair this unit. D's came in and within a short test found the problem and assured me of a fix. They made the fix within 2 days as they needed to get a part and they also checked to see what the cost would be of the fix by putting in the control boarrd from the maker which was very high to the extreme. I now have a unit working and am very pleased."
×