A mini-split system typically supplies air conditioned and heated air to a single or a few rooms of a building. Multi-zone systems are a common application of ductless systems and allow up to 8 rooms (zones) to be conditioned from a single outdoor unit. Multi-zone systems typically offer a variety of indoor unit styles including wall-mounted, ceiling-mounted, ceiling recessed, and horizontal ducted. Mini-split systems typically produce 9,000 to 36,000 Btu (9,500–38,000 kJ) per hour of cooling. Multi-zone systems provide extended cooling and heating capacity up to 60,000 Btu's.
If you need a furnace repaired or an air conditioner serviced, we'll send a local technician out to diagnose the specific problem and recommend solutions for you and your family. There will be a diagnostic fee for the visit, and any specific repairs will be an additional charge. If replacing your system is the best solution, the fee for the diagnosis will be credited toward the purchase and install of a new system.
Outside of your home is an outdoor unit, which is called a condenser. Inside the condenser is a compressor, a condenser coil, and a large fan. The compressor pumps cool refrigerant to an evaporator coil located either in the air handler or just outside the furnace. The evaporator coil gets really cold so that when the blower or furnace pushes warm air past it, the air is cooled. This cool air is then distributed throughout your home through a series of air ducts. Heat is absorbed by the evaporator coil, which warms the refrigerant moving through the coils. This warm refrigerant is then pumped back outside to the condenser coil, where a giant fan cools it off allowing the warm air to escape. This cycle is repeated until your thermostat detects that your home has reached the temperature you set it to.
If your air ducts have been damaged, you’ll need to replace them. The national average air duct replacement cost is $150-$280, which may not include materials. Factors such as duct material, labor, location of ducts and linear feet of ductwork will all affect your final costs. Labor costs will vary based on how accessible the ducts are and what material your ducts are made of. The least expensive duct material is a flexible, non-metallic ducting that costs approximately $1-$2 per linear foot. Flexible aluminum is generally more expensive and stronger than non-metallic ducting. Stainless steel ducting is the strongest, the least flexible (meaning installing it typically has higher labor rates), and usually the most expensive. An average price for air duct replacement could range between $35 and $55 per linear foot, including basic materials and labor. A typical single-family home has 6-10 duct runs; replacing or installing one duct run could average $150-$250 for labor.
From furnaces to full commercial systems and much, much more, we are committed to fantastic service and meeting our customer’s needs. If you’re looking for an emergency AC or heating repair, or just want to have a conversation about your heating and cooling needs, please give us a call at 678-235-9699, or schedule an appointment online and we’d be happy to chat with you!
Your heating and cooling equipment is vital to your comfort and breakdowns can be stressful, inconvenient and even dangerous. You can rely on the professionals at One Hour Heating and Air Conditioning* for expert service when you need it most. Our highly-trained technicians are available around the clock to meet your heating and cooling needs. We'll install, repair and maintain your HVAC system, keeping it in peak condition. Give us a call when you need to:
Refrigeration air conditioning equipment usually reduces the absolute humidity of the air processed by the system. The relatively cold (below the dewpoint) evaporator coil condenses water vapor from the processed air, much like an ice-cold drink will condense water on the outside of a glass. Therefore, water vapor is removed from the cooled air and the relative humidity in the room is lowered. The water is usually sent to a drain or may simply drip onto the ground outdoors. The heat is rejected by the condenser which is located outside of room to be cooled.
When it comes to your indoor winter comfort, you should never settle. A perfectly warm home is important to your daily life, and the performance of your heating system impacts the safety, air quality, and cost of keeping an enjoyable home. Sky Heating & Air Conditioning protects your ongoing satisfaction with a diverse range of quality heating products and services, including new system installation, replacement, seasonal maintenance, and repair. We work to improve efficiency, reliability, and safety, and deliver corner to corner temperature control throughout the rooms of your home. With 24/7 Emergency Services, you’re never left out in the cold. Contact Sky Heating & Air Conditioning for heating service in The Dalles and Portland, OR, and we’ll provide the exemplary customer service that sets us apart.
If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.