Denver HVAC Repair

   As for parts prices, we are a business and factor in profit and overhead into our pricing structure, and frequently research other companies to be sure we are competitive, which we are. Jody, you did not pay $400 for labor, you paid $489 for a flat rate repair which included, travel, labor, diagnostics, parts, tax, shipping, truck charge, fuel charge, overtime rate, profit and overhead. As for the time of the actual repair, if it had taken 2 or 3 hours the cost would have still been the same $489.        
All modern air conditioning systems, even small window package units, are equipped with internal air filters. These are generally of a lightweight gauzy material, and must be replaced or washed as conditions warrant. For example, a building in a high dust environment, or a home with furry pets, will need to have the filters changed more often than buildings without these dirt loads. Failure to replace these filters as needed will contribute to a lower heat exchange rate, resulting in wasted energy, shortened equipment life, and higher energy bills; low air flow can result in iced-over evaporator coils, which can completely stop air flow. Additionally, very dirty or plugged filters can cause overheating during a heating cycle, and can result in damage to the system or even fire.
Although your AC may continue to work for a time, if you ignore warning signs of air conditioner repair troubles, it can be much more costly to repair in the long term. Diminished cooling capacity not only makes your home uncomfortably warm, but it also raises your utility bills significantly as your unit struggles to maintain the desired temperature ineffectively. A system put under strain is likely to overheat, resulting in major damage. Therefore, it is best to have your air conditioner repaired promptly when you discover signs of trouble. 
At Reliable Comfort Heating & Air Conditioning, we combine skilled workmanship with dedicated customer service to earn your complete satisfaction.  Whether you are in need of new HVAC installation, replacement, maintenance, repair, air quality solutions, or duct sealing, we draw from extensive hands-on experience, quality products, and advanced training to maximize value and rewards.
Air conditioning and refrigeration are provided through the removal of heat. Heat can be removed through radiation, convection, or conduction. Refrigeration conduction media such as water, air, ice, and chemicals are referred to as refrigerants. A refrigerant is employed either in a heat pump system in which a compressor is used to drive thermodynamic refrigeration cycle, or in a free cooling system which uses pumps to circulate a cool refrigerant (typically water or a glycol mix).
The first air conditioners and refrigerators employed toxic or flammable gases, such as ammonia, methyl chloride, or propane, that could result in fatal accidents when they leaked. Thomas Midgley, Jr. created the first non-flammable, non-toxic chlorofluorocarbon gas, Freon, in 1928. The name is a trademark name owned by DuPont for any chlorofluorocarbon (CFC), hydrochlorofluorocarbon (HCFC), or hydrofluorocarbon (HFC) refrigerant. The refrigerant names include a number indicating the molecular composition (e.g., R-11, R-12, R-22, R-134A). The blend most used in direct-expansion home and building comfort cooling is an HCFC known as chlorodifluoromethane (R-22).
Modern air conditioning systems are not designed to draw air into the room from the outside, they only recirculate the increasingly cool air on the inside. Because this inside air always has some amount of moisture suspended in it, the cooling portion of the process always causes ambient warm water vapor to condense on the cooling coils and to drip from them down onto a catch tray at the bottom of the unit from which it must then be routed outside, usually through a drain hole. As this moisture has no dissolved minerals in it, it will not cause mineral buildup on the coils. This will happen even if the ambient humidity level is low. If ice begins to form on the evaporative fins, it will reduce circulation efficiency and cause the development of more ice, etc. A clean and strong circulatory fan can help prevent this, as will raising the target cool temperature of the unit's thermostat to a point that the compressor is allowed to turn off occasionally. A failing thermistor may also cause this problem. Refrigerators without a defrost cycle may have this same issue. Dust can also cause the fins to begin blocking air flow with the same undesirable result: ice.
The main problem when installing a multi-split system is the laying of long refrigerant lines for connecting the external unit to the internal ones. While installing a separate split system, workers try to locate both units opposite to each other, where the length of the line is minimal. Installing a multi-split system creates more difficulties, since some of indoor units can be located far from the outside. The first models of multi-split systems had one common control system that did not allow you to set the air conditioning individually for each room. However, now the market has a wide selection of multi-split systems, in which the functional characteristics of indoor units operate separately from each other.
Having trouble keeping your home cool? Not cozy enough during the winter? Aire Serv® can help you keep your home comfortable and ensure you enjoy quality air year-round! When it comes to your heating, ventilating, and air conditioning services, our team wants to make sure you can breathe easy by delivering quality air conditioning, heating and furnace repair services at an affordable rate.
Many disconnect blocks contain two cartridge fuses. Check them before you proceed with repairs (Photo 3). A blown fuse is a sign of a failing part inside the condensing unit. So don’t just replace it and think you’ve solved the problem. Instead, replace the parts we show here. Then install new fuses and fire up the unit. If it blows again, call a pro—you’ve got more serious issues.
All your HVAC needs are addressed, including finding a local heating and air conditioning contractor in your area. We offer information for a variety of brands and products in the HVAC industry, so you can care for your heating and cooling system, or know when to call a licensed HVAC contractor to repair your HVAC system. Get knowledgeable advice from the experts at HVAC.com today!

No matter where you bought your air conditioning system, we can repair it. We have years of experience working with all the best central air conditioner brands such as Kenmore, Carrier. Trane, Goodman, and Rheem. As a result, you can rest assured we’re familiar with your air conditioning system and we have the parts you need to complete a successful air conditioner repair.
Good Evening HVAC Team, I deeply appreciate your team for getting back to me quickly yesterday evening so I could schedule an appointment for my gf's place(definitely something has been wrong for a while)-- The technician Alberto showed up within the 2 hour window that was appointed to us (WITHIN the 1st half hour!!!). BIG THANK YOU for being honest, and advising us that for some reason the fuse/switch was in the reverse position so the AC unit would not properly turn on. The unit turned back on immediately, and began cooling the house. And then providing advice that the AC/Heating system needed some TLC, and giving us options to save money by purchasing a maintenance plan that included the filters plus cleaning services since we were already being charged for the service today. My personal thanks for being extremely professional, and personable as you entered our home. Solving the technical issue is only part of the job, but providing great Customer Service, and Cost Effective solutions are reasons to recommend you to the people who are looking for the same type of service. Also, it was very convenient that you were able to take my payment over the Phone(FaceTime) since I was not present at the time. Your company website is well organized, and I had no problem reviewing your capabilities as well as how to contact your team. Most important, Tina spoke very highly of you, and made her feel comfortable through the process. SO BOTTOM LINE to other customers looking for HVAC service: LOOK NO FURTHER!!! If you have a AC/Heater Issue, give this the HVAC company a call, or email-- You won't be disappointed. Kind Regards, Michael
Hospital operating theatres, in which air is filtered to high levels to reduce infection risk and the humidity controlled to limit patient dehydration. Although temperatures are often in the comfort range, some specialist procedures, such as open heart surgery, require low temperatures (about 18 °C, 64 °F) and others, such as neonatal, relatively high temperatures (about 28 °C, 82 °F).
Was not satisifed with this company. This person came out and took 10 minutes only to tell me that my unit would not last for a year and that I needed to have it replaced! I'm not sure if he was very knowlegable or if he was just plain lazy and do not even try to fix the problem. He just wanted to install a brand new system because he was both and of course, that's much more money for him!
If your unit needs more than two pounds or charged more than once a year it is recommended you have a refrigerant leak check done to your system. You most likely have a serious refrigerant leak and it needs to be repaired. Leaking units do not operate efficiently; take their toll on the environment, and can cause serious HVAC mechanical problems in the future. Lastly, a good HVAC service tech will attempt to find the refrigerant leak within the hour’s air conditioning service you are paying for in addition to the refrigerant charge.
Here’s a simple test to try on your own: When it’s hotter than 80 degrees outside, turn on your AC unit, and set it to well below room temperature. Let it run for 15 minutes, then use a thermometer to check just outside the return duct (the area where air flows in to be cooled). Now take a temperature reading just outside the strongest, most easily accessible vent (where cool air should be flowing out). Subtract the second reading from the first. If the difference between these two is fewer than 14 degrees, your HVAC unit might need work. 
The performance of vapor compression refrigeration cycles[23] is limited by thermodynamics. These air conditioning and heat pump devices move heat rather than convert it from one form to another, so thermal efficiencies do not appropriately describe the performance of these devices. The Coefficient-of-Performance (COP) measures performance, but this dimensionless measure has not been adopted. Instead, the Energy Efficiency Ratio (EER) has traditionally been used to characterize the performance of many HVAC systems. EER is the Energy Efficiency Ratio based on a 35 °C (95 °F) outdoor temperature. To more accurately describe the performance of air conditioning equipment over a typical cooling season a modified version of the EER, the Seasonal Energy Efficiency Ratio (SEER), or in Europe the ESEER, is used. SEER ratings are based on seasonal temperature averages instead of a constant 35 °C (95 °F) outdoor temperature. The current industry minimum SEER rating is 14 SEER.[24]
Occupational employment projections are developed for all states by Labor Market Information (LMI) or individual state Employment Projections offices. All state projections data are available at www.projectionscentral.com. Information on this site allows projected employment growth for an occupation to be compared among states or to be compared within one state. In addition, states may produce projections for areas; there are links to each state’s websites where these data may be retrieved.
Outside of your home is an outdoor unit, which is called a condenser. Inside the condenser is a compressor, a condenser coil, and a large fan. The compressor pumps cool refrigerant to an evaporator coil located either in the air handler or just outside the furnace. The evaporator coil gets really cold so that when the blower or furnace pushes warm air past it, the air is cooled. This cool air is then distributed throughout your home through a series of air ducts. Heat is absorbed by the evaporator coil, which warms the refrigerant moving through the coils. This warm refrigerant is then pumped back outside to the condenser coil, where a giant fan cools it off allowing the warm air to escape. This cycle is repeated until your thermostat detects that your home has reached the temperature you set it to.

Our skilled technicians arrive prepared to handle the scope of even complex malfunctions, with all makes and models of heating and cooling equipment, most often resolving the problem on the spot.  For all your HVAC service, repairs, and installations in Livermore, CA, Pleasanton, CA & Dublin, CA, call the team from Miller’s Air Conditioning & Heating!
In 1758, Benjamin Franklin and John Hadley, a chemistry professor at Cambridge University, conducted an experiment to explore the principle of evaporation as a means to rapidly cool an object. Franklin and Hadley confirmed that evaporation of highly volatile liquids (such as alcohol and ether) could be used to drive down the temperature of an object past the freezing point of water. They conducted their experiment with the bulb of a mercury thermometer as their object and with a bellows used to speed up the evaporation. They lowered the temperature of the thermometer bulb down to −14 °C (7 °F) while the ambient temperature was 18 °C (64 °F). Franklin noted that, soon after they passed the freezing point of water 0 °C (32 °F), a thin film of ice formed on the surface of the thermometer's bulb and that the ice mass was about 6 mm (1⁄4 in) thick when they stopped the experiment upon reaching −14 °C (7 °F). Franklin concluded: "From this experiment one may see the possibility of freezing a man to death on a warm summer's day."[9]

Dichlorodifluoromethane (R-12) was the most common blend used in automobiles in the U.S. until 1994, when most designs changed to R-134A due to the ozone-depleting potential of R-12. R-11 and R-12 are no longer manufactured in the U.S. for this type of application, so the only source for air-conditioning repair purposes is the cleaned and purified gas recovered from other air conditioner systems. Several non-ozone-depleting refrigerants have been developed as alternatives, including R-410A. It was first commercially used by Carrier Corp. under the brand name Puron.[citation needed]
While there's nothing you can do to guarantee your air conditioner or furnace will never need repairs, there are ways to take better care of your system. Changing out the air filters every 3-6 months, making sure nothing is obstructing or interfering with the outside unit, and keeping all vents unblocked in well-used rooms will help keep your air conditioning and heating system operating efficiently.
Compare replacement and repair costs: A new boiler or furnace is a substantial investment, but repair costs can also become costly as well. Not to mention, there’s always the possibility of the same issue occurring again or the need for more work in the future. You may want to replace your heating system if the repairs exceed half of the replacement costs.
R22 (also known as HCFC-22) has a global warming potential about 1,800 times higher than CO2.[61] It was phased out for use in new equipment by 2010, and is to be completely discontinued by 2020. Although these gasses can be recycled when air conditioning units are disposed of, uncontrolled dumping and leaking can release gas directly into the atmosphere.
You have an incredible team! My suite has had major issues constant backups. In the last few months we had a horrible flood that caused us thousands of dollars in repairs. Your team was so attentive and took care of all the repairs. Just yesterday another back up called them immediately and like quick responders they were there to take of it! A huge thank you from my La Costa providers and staff! We appreciate your hard and dedicated work!
So HVAC sent Tony Diaz to my house. I was at work so he was subjected to the most excruciatingly exacting woman on the planet (my wife). Tony impressed her with his friendliness, professionalism and the obvious jouneyman-level knowledge of his craft. He found literally --burnt-out-- parts in our system and replaced them. It cost us a bit but I know enough about the parts to see there was no gouging on the parts and a fair rate for the labor. It wasn't cheap but it was fair and worth every dime.
Abacus’ residential and commercial plumbers are proficient at repairing all kinds of plumbing issues, including gas and electric water heaters, slab leaks, leaky pipes to hydro jetting clogged drains. Many plumbing problems are not DIY types of jobs, call Abacus so one of our licensed plumbers can fix your problem. Our plumbers are not only knowledgeable but their customer service skills will meet or exceed your expectations.
AC air handler buzzing sounds. Do you hear a buzzing sound when you turn on the thermostat? The only thing that comes on in the house when you turn on the thermostat is the fan relay and fan in the air handler or furnace. Try switching the thermostat HEAT/COOL switch to OFF. Then switch the fan switch from AUTO to ON. The fan (only) should come on. If the air handler makes a buzzing sound, it probably has a bad fan relay or, more likely, blower fan.
A.J. LeBlanc Heating specializes in the installation and service of heating, air conditioning and plumbing systems for residential homes. Whether you are building a new home, converting your existing heating system to a different fuel, upgrading your old unit to a more efficient system, or just adding air conditioning, LeBlanc Heating can service your needs.
Beyond changing the air filter on a regular basis, one of the best ways to ensure your home's HVAC system is operating at peak efficiency is to have a qualified professional HVAC contractor tune up the system on a biannual basis. Energy Star recommends scheduling your system tune-up around the beginning of daylight savings time in the fall and its end in the spring. It's an easy way to remember to have your system serviced before the peak heating and cooling seasons. A standard tune-up is likely to cost you between $70 and $100, but it's money well spent. 
With winter on its way back to Atlanta, furnace and heating repair may not be the first thing you think about, but maybe it should be. Sure, it’s easy for us to sit here and tell you to arrange annual furnace service, but it’s only because we want to help you avoid a heating breakdown during the coldest day of the month in Atlanta. Day or night, our HVAC experts are here to ensure you have a comfortable home, and can help get your furnace back operating in almost no time.
Many disconnect blocks contain two cartridge fuses. Check them before you proceed with repairs (Photo 3). A blown fuse is a sign of a failing part inside the condensing unit. So don’t just replace it and think you’ve solved the problem. Instead, replace the parts we show here. Then install new fuses and fire up the unit. If it blows again, call a pro—you’ve got more serious issues.
×