Every Trane system is tested in some of the most extreme conditions found in nature to ensure they’re truly unstoppable – like freezing conditions in our System Extreme Environmental Test (SEET) lab. That’s where engineers put units through five years of wear and tear in just a few months, to get a product you can count on to run through anything. We never settle, so they never stop.
Camera, Video & SurveillanceAction Cameras & Drones,Camcorders,Dash...3504 Car Electronics & GPSCar Audio,Car Mounts & Accessories,Car S...1802 Cell Phones & AccessoriesBackup Batteries,Bluetooth Devices,Cable...12628 Computers & TabletsComputer Accessories,Desktops, Monitors...5511 Musical InstrumentsAccessories,Amplifiers & Effects,Brass &...1909 Office Electronics & SuppliesNetworking,Printers & Scanners,Scanners...2201 Portable AudioBluetooth & Wireless Speakers,Docks, Rad...3233 Smart HomeCameras & Surveillance,Door Locks,Garage...104
Outside of your home is an outdoor unit, which is called a condenser. Inside the condenser is a compressor, a condenser coil, and a large fan. The compressor pumps cool refrigerant to an evaporator coil located either in the air handler or just outside the furnace. The evaporator coil gets really cold so that when the blower or furnace pushes warm air past it, the air is cooled. This cool air is then distributed throughout your home through a series of air ducts. Heat is absorbed by the evaporator coil, which warms the refrigerant moving through the coils. This warm refrigerant is then pumped back outside to the condenser coil, where a giant fan cools it off allowing the warm air to escape. This cycle is repeated until your thermostat detects that your home has reached the temperature you set it to.
When you trust your winter comfort to Edwards Heating & Air, we answer with state-of-the-art technology, NATE-certified technicians, and prompt action. As a Carrier Factory Authorized Dealer, we specialize in the most proven and sophisticated solutions to home and commercial temperature control. Through ongoing factory training and strict installation and service procedures, the team from Edwards Heating & Air delivers superior workmanship and superior results. We ensure your demands for efficiency, reliability, and consistent heating are met, and your expectations for courteous and skilled service are exceeded. Whether you are in the process of building your dream home, in need of effective heating for your existing home or business, or upgrading your furnace or heat pump, our installation specialists provide informed recommendations, attention to detail, and quick turnaround on your project. Serving Acworth and the surrounding areas of Acworth, Alpharetta, Cummings, Cartersville, Kennesaw & Woodstock, GA since 2001, you can count on Edwards Heating & Air for everything from installation and maintenance to emergency repairs.
In addition to air cleanliness, we provide expert services in air conditioning sales, installation, and maintenance, furnaces, heat pumps, packaged systems, and more. Chances are that if you have a concern when it comes to HVAC, we can solve your problem. Our technicians in Mableton will walk you through the service you need, how to fill your need most cost-effectively, and provide a 100% guarantee on the services we provide – each time.
In very dry climates, evaporative coolers, sometimes referred to as swamp coolers or desert coolers, are popular for improving coolness during hot weather. An evaporative cooler is a device that draws outside air through a wet pad, such as a large sponge soaked with water. The sensible heat of the incoming air, as measured by a dry bulb thermometer, is reduced. The temperature of the incoming air is reduced, but it is also more humid, so the total heat (sensible heat plus latent heat) is unchanged. Some of the sensible heat of the entering air is converted to latent heat by the evaporation of water in the wet cooler pads. If the entering air is dry enough, the results can be quite substantial.
All your HVAC needs are addressed, including finding a local heating and air conditioning contractor in your area. We offer information for a variety of brands and products in the HVAC industry, so you can care for your heating and cooling system, or know when to call a licensed HVAC contractor to repair your HVAC system. Get knowledgeable advice from the experts at HVAC.com today!
Air conditioning units work by using evaporator and condenser coils to remove heat from the air in your home. Warm household air blows through the evaporator coils, which transfer the heat into refrigerant vapor, which is then moved to the condenser in the outdoor part of the unit. The condenser coils turn the now-warm refrigerant vapor into liquid, allowing the heat to be dispersed outside and away from your home.
Need Air Conditioner Repair or Furnace Repair? Look no further. The HVAC experts at Allatoona Heating and Air are here to help you today. We have the training and experience necessary to handle all sorts of heating and air conditioning issues for all brands of heating and air equipment. We’re not limited to repairs either. Our HVAC technicians can help you with repairs, service, maintenance, replacement or installation of heating and air conditioning equipment for your home or office. Call us today!
Here’s a simple test to try on your own: When it’s hotter than 80 degrees outside, turn on your AC unit, and set it to well below room temperature. Let it run for 15 minutes, then use a thermometer to check just outside the return duct (the area where air flows in to be cooled). Now take a temperature reading just outside the strongest, most easily accessible vent (where cool air should be flowing out). Subtract the second reading from the first. If the difference between these two is fewer than 14 degrees, your HVAC unit might need work.
Before you service an air conditioner, make sure the unit is turned completely off by unplugging or shutting off the circuit breaker. Then, rake off any debris from the unit and use a soft brush to remove dirt from the outside cover. If the small copper pipe connecting the unit to the house feels hot, the unit’s coils likely needs to be washed. Remove the outside cover, cover the motor and wiring with a plastic sheet, and hose down the fins, coils, and inside of the unit. Finally, replace the cover when you’re done.