Denver HVAC Repair

If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.


Here’s a simple test to try on your own: When it’s hotter than 80 degrees outside, turn on your AC unit, and set it to well below room temperature. Let it run for 15 minutes, then use a thermometer to check just outside the return duct (the area where air flows in to be cooled). Now take a temperature reading just outside the strongest, most easily accessible vent (where cool air should be flowing out). Subtract the second reading from the first. If the difference between these two is fewer than 14 degrees, your HVAC unit might need work. 
Monday the following week, no phone calls, or follow up.  I call to get an update and am told that they cannot install my system because they don't have time.  I ask what does that mean, one year? One week? Until the end of summer they say.  What does that mean I ask?  They say at the end of September.  I say thank you for wasting 1 month of my time.

A career in this field may require you to meet certain licensing, training, and other requirements that can vary by vocation and state. You should check with your state, local government, and/or licensing board to find out which requirements may be applicable in your state. Click here for contact information on state licensing/regulatory boards and certain professional licensing information.
West Michigan residents and business owners trust Service Professor with their indoor air comfort. And you can too. No matter your AC problem you can rely on Service Professor to deliver. Whether it’s routine maintenance or unexpected AC repairs or a new system installation, you can count on your West Michigan HVAC technicians to offer great service.

Whether you’re looking for air conditioning maintenance, air conditioner repair, or a new air conditioning system, Sears Home Services can help. We’re your best, most-trusted option for fast, quick, and easy local service, repair, and maintenance of your home air conditioning system. If your air conditioner isn’t cooling or your central air conditioner is leaking water, we’ll connect you to the best local AC repair service technicians in the business.We have local technicians in your neighborhood that are highly trained, licensed, vetted, and guaranteed to help fix all of your air conditioning needs.
BIG THANK YOU for being honest, and advising us that for some reason the fuse/switch was in the reverse position so the AC unit would not properly turn on.   The unit turned back on immediately, and began cooling the house.   And then providing advice that the AC/Heating system needed some TLC, and giving us options to save money by purchasing a maintenance plan that included the filters plus cleaning services since we were already being charged for the service today.

Free cooling systems can have very high efficiencies, and are sometimes combined with seasonal thermal energy storage so that the cold of winter can be used for summer air conditioning. Common storage mediums are deep aquifers or a natural underground rock mass accessed via a cluster of small-diameter, heat-exchanger-equipped boreholes. Some systems with small storages are hybrids, using free cooling early in the cooling season, and later employing a heat pump to chill the circulation coming from the storage. The heat pump is added-in because the storage acts as a heat sink when the system is in cooling (as opposed to charging) mode, causing the temperature to gradually increase during the cooling season.


As we all know, San Diego can get pretty warm in the summer and also quite chilly in the winter. So, in order to avoid discomfort, it is important to ensure your heating and air conditioning systems are working properly beforehand. That’s where our HVAC San Diego professionals come in. Our crew members have both the knowledge and expertise to ensure that every heating and air conditioning unit, no matter the make or model, is running at peak performance.
All modern air conditioning systems, even small window package units, are equipped with internal air filters. These are generally of a lightweight gauzy material, and must be replaced or washed as conditions warrant. For example, a building in a high dust environment, or a home with furry pets, will need to have the filters changed more often than buildings without these dirt loads. Failure to replace these filters as needed will contribute to a lower heat exchange rate, resulting in wasted energy, shortened equipment life, and higher energy bills; low air flow can result in iced-over evaporator coils, which can completely stop air flow. Additionally, very dirty or plugged filters can cause overheating during a heating cycle, and can result in damage to the system or even fire.
“Robinson Air = top notch professionals. Mike was personable, knowledgeable, timely, thorough, and left me with a hard copy of prioritized recommendations and his explanations of HVAC needs I may have in the future. I was very impressed with being shown a tablet picture of a possible problem. It was so refreshing to have the service and all phone interactions handled so well and smoothly…thank you for taking the “angst” out of this kind of service call. My hat is off to you and I will happily recommend you to family and friends. Thank you!!!”
The cost of service varies widely from one region to the next so it is next to impossible to give you prices for air conditioning service. The best way to check prices is to shop around. Be aware though that sometimes the cheapest price for HVAC air conditioning and heating service and repair is not always the best way to go. Your main concern should be getting knowledgeable HVAC service technicians, reliability, punctuality, honesty, integrity, and guaranteed work.
Dichlorodifluoromethane (R-12) was the most common blend used in automobiles in the U.S. until 1994, when most designs changed to R-134A due to the ozone-depleting potential of R-12. R-11 and R-12 are no longer manufactured in the U.S. for this type of application, so the only source for air-conditioning repair purposes is the cleaned and purified gas recovered from other air conditioner systems. Several non-ozone-depleting refrigerants have been developed as alternatives, including R-410A. It was first commercially used by Carrier Corp. under the brand name Puron.[citation needed]
Inside the unit, the air passes over the evaporator coil first, and is cooled and dehumidified. The now dehumidified, cold air then passes over the condenser coil where it is warmed up again. Then the air is released back into the room. The unit produces warm, dehumidified air and can usually be placed freely in the environment (room) that is to be conditioned.
“We had a great experience with Robinson’s! The office staff, then the gentleman who helped me with questions over the phone and Kyle, our service tech, were all great and very easy to work with. They gave me a time frame for when to expect Kyle the same day. A phone call to let me know he was on his way. A text with picture so I knew who to be expecting. Kyle arrived on time and was very knowledgeable and friendly. He did a great job. You could tell he liked his job. Prices were reasonable. We will be using and recommending Robinson’s Air – Wichita Falls in the future.”
We’ve found that many homes and businesses in Atlanta face significant indoor air quality issues as a result of the seasonal high humidity in our area, which creates conditions ripe for mold and mildew growth in both old and new HVAC systems. Our HVAC technicians can help you determine which strategies will work best for neutralizing airborne particulates in your home, which often involves a combination of filtration methods and ultraviolet light technology that together can help keep your system perpetually free of contaminants. We can also install whole-house dehumidifiers and humidifiers, which can make a huge difference in the amount of work your HVAC unit will have to do to be effective.
After discussing faulty AC system symptoms with you, Jiffy Lube® technicians begin the service by visually inspecting the air conditioning compressor drive belt, serpentine belt and all accessible components for cracks, leaks or damage. Then they check the operation of the air conditioning compressor. If no leaks or damage are found, they evacuate the refrigerant from the system, vacuum test it, and recharge the air conditioning system using the appropriate refrigerant according to your vehicle manufacturer's recommendations.
The quality of the air you breathe affects your comfort, health, and productivity.  Whether at home or in the workplace, an ample supply of fresh, clean air is essential to everyday life.  Whatever concerns you may face, Edwards Heating & Air provides proven, cost-effective products to significantly improve Indoor Air Quality.  Our NATE-certified specialists are qualified to analyze your residential or commercial space, make informed recommendations, and implement a strategy specifically targeted at your unique circumstances.  As a Carrier Factory Authorized Dealer, we are extensively trained in leading-edge products that silently and effectively eliminate harmful bacteria, fumes, chemicals, viruses, smoke, and much more.  The installation of a humidifier, ventilator, air filter, or UV lamp will protect the health of your indoor breathing air, maintain a cleaner, more comfortable home, and even reduce energy costs.  Contact the specialists from Edwards Heating & Air for trusted solutions and complete peace of mind.  
And Berkeys is a licensed HVAC contractor and air conditioning company offering AC repair, Air Conditioning tune-up, and air conditioning replacement services in 75001, 75006, 75007, 75010, 75019, 75038, 75039, 75062, 75063, 75080, 75081, 75082, 75234, 75248, 75252, 75287, 75061, 75060, 75201, 75202, 75203, 75204, 75205, 75206, 75207, 75208, 75209, 75210, 75211, 75212, 75214, 75215, 75216, 75217, 75218, 75219, 75220, 75221, 75222, 75223, 75224, 75225, 75226, 75227, 75228, 75229, 75230, 75231, 76092, 76179 and more. Call to confirm service for your home.

In addition to air cleanliness, we provide expert services in air conditioning sales, installation, and maintenance, furnaces, heat pumps, packaged systems, and more. Chances are that if you have a concern when it comes to HVAC, we can solve your problem. Our technicians in Mableton will walk you through the service you need, how to fill your need most cost-effectively, and provide a 100% guarantee on the services we provide – each time.

The summers here in Alexandria can range from almost pleasant to downright brutal. And you know as well as we do that it’s those latter days when your central AC or heat pump will decide to go down! But you needn’t seek solace at the Waterfront or over at Cameron Run Regional Park. The secret to restoring your comfort lies with the certified specialists at HVAC Unlimited!
Check your filter every month, especially during heavy use months (winter and summer). If the filter looks dirty after a month, change it. At a minimum, change the filter every 3 months. A dirty filter will slow down air flow and make the system work harder to keep you warm or cool — wasting energy. A clean filter will also prevent dust and dirt from building up in the system — leading to expensive maintenance and/or early system failure.
Other workers sometimes help HVACR technicians install or repair cooling and heating systems. For example, on a large air conditioning installation job, especially one in which workers are covered by union contracts, ductwork may be installed by sheet metal workers, electrical work by electricians, and pipework by plumbers, pipefitters, and steamfitters. Boiler systems are sometimes installed by a boilermaker.
As much as half of the energy used in your home goes to heating and cooling. So making smart decisions about your home's heating, ventilating, and air conditioning (HVAC) system can have a big effect on your utility bills — and your comfort. Take these steps to increase the efficiency of your heating and cooling system. For more information, see our Guide to Energy Efficient Heating & Cooling (708KB).
You haven’t had a ductwork inspection in years: According to PG&E, the average home’s ductwork leaks up to 30 percent of its air before it actually reaches your living space. That means you’re still paying for the energy used to cool the air—without getting the relief of a cool home. Hire a technician to come take a look at your system; they can perform what’s called a duct-leakage test, which measures how much air is escaping the system. If it turns out your ducts are faulty or have significant gaps, a technician should be able to seal them up or replace your pipes—meaning you might not need a complete system overhaul. However, keep in mind that modern HVAC units are almost always more efficient thanks to technology advancements. In the end, you have to weigh your options: will you need to perform repairs each month?
5) Check certifications. Many HVAC professionals belong to the Air Conditioning Contractors of America (ACCA) or the Sheet Metal and Air Conditioning Contractors’ National Association (SMACNA). Both sites provide listings of HVAC contractors by area. Look for contractors whose technicians are certified by North American Technician Excellence (NATE) and partnered with ENERGY STAR.
In the refrigeration cycle, heat is transported from a colder location to a hotter area. As heat would naturally flow in the opposite direction, work is required to achieve this. A refrigerator is an example of such a system, as it transports the heat out of the interior and into its environment. The refrigerant is used as the medium which absorbs and removes heat from the space to be cooled and subsequently ejects that heat elsewhere.
We have been using Bill Howe Plumbing's service for more than 25 years and have been pleasantly surprised at how consistently they perform an excellent service call. We use them for our home and our rental properties, and their dispatchers and technicians have always been the best at problem solving; our tenants have told us how great the service is as well. When we needed air conditioning service, naturally we called Bill Howe first. There's no reason to call anyone else. I know the job will be done right the first time, with fair pricing and professional service.
Not obvious is the fact that they need maintenance routinely, just like any other machine. The filter, usually located behind the front grill, needs to be washed. The condenser coil at the back of the unit can accumulate a lot of debris, and might require a special chemical bath. All air conditioning systems, large or small, need good air flow across the evaporator coil and the condenser coil. Efficiency and performance drop rapidly as air flow decreases. Lose enough air flow and the unit will burn out. Rodents can nest inside when not in use, and can foul up the unit in many ways. Wasps and hornets, as well as the honey bee find finned coils to be comfortable nesting places. Nests and dead insects can ruin the air conditioner.
In the most general sense, air conditioning can refer to any form of technology that modifies the condition of air (heating, (de-)humidification, cooling, cleaning, ventilation, or air movement). In common usage, though, "air conditioning" refers to systems which cool air. In construction, a complete system of heating, ventilation, and air conditioning is referred to as HVAC.[3]

Other than mineral deposits, the most common problem is sediment in the water supply. The float inlet valve has a tiny hole that easily clogs. The float is usually made of plastic, and if cracked will fill with water and sink. The valve will be stuck open and the reservoir will overflow. Use caution when scraping deposits off the float. If the deposits cannot be removed, replace the float or it will sink and cause an overflow.

Most modern air-conditioning systems feature a dehumidification cycle during which the compressor runs while the fan is slowed as much as possible[citation needed] to reduce the evaporator temperature and therefore condense more water. When the temperature falls below a threshold, both the fan and compressor are shut off to mitigate further temperature drops;[clarification needed] this prevents moisture on the evaporator from being blown back into the room.[citation needed] When the temperature rises again,[clarification needed] the compressor restarts and the fan returns to low speed.
In the UK, the Ozone Regulations[62] came into force in 2000 and banned the use of ozone depleting HCFC refrigerants such as R22 in new systems. The Regulation banned the use of R22 as a "top-up" fluid for maintenance between 2010 (for virgin fluid) and 2015 (for recycled fluid). This means that equipment that uses R22 can still operate, as long as it does not leak. Although R22 is now banned, units that use the refrigerant can still be serviced and maintained.
I could not have been more pleased with the responsiveness, considerate employees, workmanship, and follow up. We used three divisions of Bill Howe when we had a flood due to a water heater/T&P gauge, Plumbing, Remediation and Reconstruction. It was timely, reasonably priced and finished with attention to detail. Ashley in the office was always polite and responsive and we could not have been happier under the circumstances.
HVACNearYou.com is the number one directory for HVAC service. HVAC service is a must when facing air conditioner or heating issues. With HVAC repair and service, your cooling/heating systems will be up and running before you know it - from central heating and cooling to window units, and all ventilation systems in between, HVAC service and repair can make your units work again. With thousands of HVAC service and repair shops/contractors listed and more added each day, HVACNearYou.com will help you find the most reliable and affordable HVAC service in your area.
We’ve found that many homes and businesses in Atlanta face significant indoor air quality issues as a result of the seasonal high humidity in our area, which creates conditions ripe for mold and mildew growth in both old and new HVAC systems. Our HVAC technicians can help you determine which strategies will work best for neutralizing airborne particulates in your home, which often involves a combination of filtration methods and ultraviolet light technology that together can help keep your system perpetually free of contaminants. We can also install whole-house dehumidifiers and humidifiers, which can make a huge difference in the amount of work your HVAC unit will have to do to be effective.

The use of furnaces, space heaters, and boilers as a method of indoor heating could result in incomplete combustion and the emission of carbon monoxide, nitrogen oxides, formaldehyde, volatile organic compounds, and other combustion byproducts. Incomplete combustion occurs when there is insufficient oxygen; the inputs are fuels containing various contaminants and the outputs are harmful byproducts, most dangerously carbon monoxide, which is a tasteless and odorless gas with serious adverse health effects.[14]
Modern refrigerants have been developed to be more environmentally safe than many of the early chlorofluorocarbon-based refrigerants used in the early- and mid-twentieth century. These include HCFCs (R-22, as used in most U.S. homes before 2011) and HFCs (R-134a, used in most cars) have replaced most CFC use. HCFCs, in turn, are supposed to have been in the process of being phased out under the Montreal Protocol and replaced by HFCs such as R-410A, which lack chlorine.[14] HFCs, however, contribute to climate change problems. Moreover, policy and political influence by corporate executives resisted change.[15][16] Corporations insisted that no alternatives to HFCs existed. The environmental organization Greenpeace provided funding to a former East German refrigerator company to research an alternative ozone- and climate-safe refrigerant in 1992. The company developed a hydrocarbon mix of isopentane and isobutane, but as a condition of the contract with Greenpeace could not patent the technology, which led to its widespread adoption by other firms.[17][18][19] Their activist marketing first in Germany led to companies like Whirlpool, Bosch, and later LG and others to incorporate the technology throughout Europe, then Asia, although the corporate executives resisted in Latin America, so that it arrived in Argentina produced by a domestic firm in 2003, and then finally with giant Bosch's production in Brazil by 2004.[20][21]
I could not have been more pleased with the responsiveness, considerate employees, workmanship, and follow up. We used three divisions of Bill Howe when we had a flood due to a water heater/T&P gauge, Plumbing, Remediation and Reconstruction. It was timely, reasonably priced and finished with attention to detail. Ashley in the office was always polite and responsive and we could not have been happier under the circumstances.
Your HVAC professional can perform a yearly tune-up of your system for around $80-$100. This yearly maintenance can go far toward heading off major repairs to your system, and provide you with peace of mind and considerable savings in the long term. Additionally, regular servicing of your AC unit can help a home inspector to certify that your unit is working properly in the event you decide to sell your home.
One problem occurred on Monday.  When we called at 2:30 in the afternoon to check on status, we were told that "the tech is on the phone with the parts supplier now".  It seems more likely that they had forgotten about us and our call woke them up.  But even if true, why the heck did they wait until 2:30 to order the part?  Maybe if they had ordered it in the morning they could have had it the same day.  So I'm taking off one star for that.
“We had a great experience with Robinson’s! The office staff, then the gentleman who helped me with questions over the phone and Kyle, our service tech, were all great and very easy to work with. They gave me a time frame for when to expect Kyle the same day. A phone call to let me know he was on his way. A text with picture so I knew who to be expecting. Kyle arrived on time and was very knowledgeable and friendly. He did a great job. You could tell he liked his job. Prices were reasonable. We will be using and recommending Robinson’s Air – Wichita Falls in the future.”
I originally took off one star because of the SNAFU with getting the part ordered.  When Alberto called me on the phone he admitted the person had "gotten busy with other things" and apologized.  THAT was taking the high road and I was impressed by that.  Sadly, for reasons I won't guess at, Alberto has decided to take the low road in his comments and imply that they got the part as quickly as possible.  Well, we called at 2:30 so did someone spend six and a half hours finding the part??  That seems very doubtful.
The use of CFC as a refrigerant was once common, including the refrigerants R-11 and R-12 (sold under the brand name Freon-12). Freon refrigerants were commonly used during the 20th century in air conditioners due to their superior stability and safety properties. When they are released accidentally or deliberately, these chlorine-bearing refrigerants eventually reach the upper atmosphere.[60] Once the refrigerant reaches the stratosphere, UV radiation from the Sun homolytically cleaves the chlorine-carbon bond, yielding a chlorine radical. These chlorine radicals catalyze the breakdown of ozone into diatomic oxygen, depleting the ozone layer that shields the Earth's surface from strong UV radiation. Each chlorine radical remains active as a catalyst until it binds with another radical, forming a stable molecule and quenching the chain reaction.
Your home’s HVAC system is a fine-tuned piece of machinery. Like your car, your system needs regular maintenance and tune-ups to ensure it is running reliably. Manufacturer warranties for most new systems require annual tune-ups, and for good reason: these preventative maintenance measures extend the life of your system by keeping your system running the way it is designed to run.

Not obvious is the fact that they need maintenance routinely, just like any other machine. The filter, usually located behind the front grill, needs to be washed. The condenser coil at the back of the unit can accumulate a lot of debris, and might require a special chemical bath. All air conditioning systems, large or small, need good air flow across the evaporator coil and the condenser coil. Efficiency and performance drop rapidly as air flow decreases. Lose enough air flow and the unit will burn out. Rodents can nest inside when not in use, and can foul up the unit in many ways. Wasps and hornets, as well as the honey bee find finned coils to be comfortable nesting places. Nests and dead insects can ruin the air conditioner.


I have a recurring problem of having to have freon added to my A/C system. I have even replaced both units inside and outside but seem to have the same problem. I believe that it must be in the lines between the outside and inside. Is there anything that can be put into the lines to seal any leaks if this is the problem? If not is it advised that the lines be replaced?
The most recognized standards for HVAC design are based on ASHRAE data. The most general of four volumes of the ASHRAE Handbook is Fundamentals; it includes heating and cooling calculations. Each volume of the ASHRAE Handbook is updated every four years. The design professional must consult ASHRAE data for the standards of design and care as the typical building codes provide little to no information on HVAC design practices; codes such as the UMC and IMC do include much detail on installation requirements, however. Other useful reference materials include items from SMACNA, ACGIH, and technical trade journals.
Baby DiaperingChanging Pads & Covers,Changing Tables,D...430 Baby FeedingBaby Food & Formula,Baby Food Prep,Bibs...696 Baby Toys939 Baby's FashionBaby's Fashion Accessories,Clothing,Sock...1476 Bath & PottyBaby Bath Tubs,Baby Toiletries,Baby Wash...424 Books, Music & MoviesKid's Music,Kids & Family Movies,Kids Bo...419 Car SeatsBases,Booster,Car Seat & Stroller Toys,C...163 Gear & ActivityBaby Carriers,Diaper Bags,Entertainers &...342
Our A/C was blowing hot air intermittently...it was cold one minute and warm the next. By 8pm I'd have a 90 degree interior temp. After one company just took a cursory glance at our A/C and found nothing wrong, I called HVAC. I called them mostly based on Michael W's post on 8/10/14 where he told us the owner, Alberto, took his feedback and took it SERIOUSLY. That speaks VOLUMES to anyone who has been around long enough to know the characteristics of the serious players are and those who are the wannabes. So HVAC sent Tony Diaz to my house. I was at work so he was subjected to the most excruciatingly exacting woman on the planet (my wife). Tony impressed her with his friendliness, professionalism and the obvious jouneyman-level knowledge of his craft. He found literally --burnt-out-- parts in our system and replaced them. It cost us a bit but I know enough about the parts to see there was no gouging on the parts and a fair rate for the labor. It wasn't cheap but it was fair and worth every dime. And now i have A/C in my house again and a repairman came to my house, actually FIXED something AND managed to do so in a friendly & professional manner. That used to be commonplace...nowadays it deserves a "Wow".. Thank you, Tony!
"Friendly, professional, responded quickly to my problem. I have called many air conditioning companies about my problem including the maker of the unit and had come to the conclusion that I would not find someone to repair this unit. D's came in and within a short test found the problem and assured me of a fix. They made the fix within 2 days as they needed to get a part and they also checked to see what the cost would be of the fix by putting in the control boarrd from the maker which was very high to the extreme. I now have a unit working and am very pleased."
×