Denver HVAC Repair

A.J. LeBlanc Heating specializes in the installation and service of heating, air conditioning and plumbing systems for residential homes. Whether you are building a new home, converting your existing heating system to a different fuel, upgrading your old unit to a more efficient system, or just adding air conditioning, LeBlanc Heating can service your needs.

If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
A contactor is a $25 mechanical relay that uses low-voltage power from the thermostat to switch 220-volt high-amperage current to the compressor and condenser fan. AC contactors can wear out and are at the top of the list of common air conditioning service failures. Even if your contactor is working, it pays to replace it every five years or so. Unscrew the old contactor before removing the wires. Then move the wires to the new unit (photo 6).

The HVAC industry is a worldwide enterprise, with roles including operation and maintenance, system design and construction, equipment manufacturing and sales, and in education and research. The HVAC industry was historically regulated by the manufacturers of HVAC equipment, but regulating and standards organizations such as HARDI, ASHRAE, SMACNA, ACCA, Uniform Mechanical Code, International Mechanical Code, and AMCA have been established to support the industry and encourage high standards and achievement.


Our Technicians are NATE Certified, licensed TACLA00078831E,  and will arrive in vehicles fully stocked so that the repair can be done the same day. When it comes to system performance, we are the pros. We have had extensive training in residential and commercial air balancing which means we can dial in your system to perform at maximum levels. We specialize in home or business air conditioning service and repair.
"HVAC Service" has found success throughout the years by evaluating overall system performance, ease of installation, reliability and long term energy consumption costs, and how these variables relate to an owner's needs.  Through innovative engineering, comprehensive design solutions, consistent work quality, and qualified maintenance; "HVAC Service" confidently delivers the best possible solutions for your business.
This is a very common air conditioning problem. The unit will cool for a few hours and then it stops cooling all together. The next day or several hours later the air conditioning is cooling again but for only a few hours and then the air conditioning stops again. The reason this is happening is because the air conditioning unit is low on refrigerant because you have a refrigerant leak (the unit could freeze because of a few other air conditioning problems but this is the most common reason).
Berkeys knows how unbearable the Dallas, Plano, Fort Worth and Arlington Texas summers can be. Assuring your home’s air conditioning system is functioning properly is our job! We’ll always have the solution to your air conditioning problem, and we’ll rescue you when your system stops working. Call us or schedule your service online today and we think you will see why we are considered to be one of the Best A/C Companies in the Dallas & Fort Worth area!

Heaters are appliances whose purpose is to generate heat (i.e. warmth) for the building. This can be done via central heating. Such a system contains a boiler, furnace, or heat pump to heat water, steam, or air in a central location such as a furnace room in a home, or a mechanical room in a large building. The heat can be transferred by convection, conduction, or radiation.
In 1820, English scientist and inventor Michael Faraday discovered that compressing and liquefying ammonia could chill air when the liquefied ammonia was allowed to evaporate. In 1842, Florida physician John Gorrie used compressor technology to create ice, which he used to cool air for his patients in his hospital in Apalachicola, Florida. He hoped to eventually use his ice-making machine to regulate the temperature of buildings. He even envisioned centralized air conditioning that could cool entire cities. Though his prototype leaked and performed irregularly, Gorrie was granted a patent in 1851 for his ice-making machine. Though his process improved the artificial production of ice, his hopes for its success vanished soon afterwards when his chief financial backer died and Gorrie did not get the money he needed to develop the machine. According to his biographer, Vivian M. Sherlock, he blamed the "Ice King", Frederic Tudor, for his failure, suspecting that Tudor had launched a smear campaign against his invention. Dr. Gorrie died impoverished in 1855, and the dream of commonplace air conditioning went away for 50 years.[citation needed]
At R&R Heating & Air Conditioning, we’re proud of our reputation built on honesty, quality and service. Our family-owned and operated company has been serving Orland Park, Tinley Park, Palos, Oak Lawn and surrounding communities since 1986. Our goal is to help you create and maintain a healthy indoor climate in your home or commercial building. Using our high-efficiency HVAC systems, you’ll use less energy, cut down on utility costs and live and work in comfortable interior spaces year-round.
"HVAC Service" has found success throughout the years by evaluating overall system performance, ease of installation, reliability and long term energy consumption costs, and how these variables relate to an owner's needs.  Through innovative engineering, comprehensive design solutions, consistent work quality, and qualified maintenance; "HVAC Service" confidently delivers the best possible solutions for your business.

Check your filter every month, especially during heavy use months (winter and summer). If the filter looks dirty after a month, change it. At a minimum, change the filter every 3 months. A dirty filter will slow down air flow and make the system work harder to keep you warm or cool — wasting energy. A clean filter will also prevent dust and dirt from building up in the system — leading to expensive maintenance and/or early system failure.
a/c compressor needed replacing. the A Team Mechanical found a way to return the next day to complete the repairs and made sure the system was running effectively. Even put down another concrete base pad to level the a/c unit. They were professionals and straight forward with the services needed. All the other HVAC companies wanted to charge me three time the amount for the services.

As one of the most trusted commercial HVAC service companies in the Midwest, not only will you receive prompt service, you won’t have to worry about our teams’ knowledge and corrective service capabilities. In the last 18 months, we’ve performed more than 3,790 mechanical preventive maintenance inspections. Whether you're in need of basic air conditioner maintenance or full commercial heating and air conditioning repair, we have yet to find a deficiency we can't fix.

Promotion lasts for 1 year from date of purchase. After that period, your voucher is redeemable for the amount you paid, less any value you may have received. Not valid as payment for Eat24 purchases. Not valid with other vouchers, certificates, or offers. Only 1 voucher(s) can be purchased and redeemed per person. Up to 3 can be purchased as gifts for others. Subject to the General Terms. Learn more View more
AutomotiveCar Care,Car Electronics,Car Safety & Se...8511 ElectricalBatteries,Extension Cords & Power Strips...2333 Fire Pits & Outdoor Heaters151 Grills & AccessoriesGrill Covers,Grilling Accessories,Grills...775 Hand & Power ToolsHand Tools,Power Tool Accessories,Power...6450 Heating & CoolingAir Conditioners,Dehumidifiers,Draft Sto...1557 Home ImprovementAppliances,Bathroom Faucets,Building Mat...10774 LightingCeiling Fans,Fixtures,Flood Lights & Sec...2657
Some systems include an "economizer mode", which is sometimes called a "free-cooling mode". When economizing, the control system will open (fully or partially) the outside air damper and close (fully or partially) the return air damper. This will cause fresh, outside air to be supplied to the system. When the outside air is cooler than the demanded cool air, this will allow the demand to be met without using the mechanical supply of cooling (typically chilled water or a direct expansion "DX" unit), thus saving energy. The control system can compare the temperature of the outside air vs. return air, or it can compare the enthalpy of the air, as is frequently done in climates where humidity is more of an issue. In both cases, the outside air must be less energetic than the return air for the system to enter the economizer mode.
As a Bryant® dealer, with a wide variety of products to choose from, we can keep your family healthy and feeling comfortable all year long. We carry a complete line of indoor comfort equipment with innovations that raise the standards of comfort and reliability, including air conditioners, heat pumps, gas furnaces, programmable thermostats, humidifiers, ductless split systems, geothermal systems, boilers, air cleaners, ultra violet lights, ventilators and zoning products. Let the experts at HVAC Services Unlimited, Inc. help you customize a solution that's right for you.
Abacus’ plumbers are also experts at sewer & pipe repairs, shower & tub repairs/installations, kitchen & bath faucet repair/installations, sink repairs/installation, plumbing inspections, water filtration, water softening, garbage disposal repair/installation, toilet repair/replacement, drain cleaning with drain camera inspections, leak detection/repair, plumbing repair/installation and back flow prevention for all Houston Texas homes & commercial business properties. Need an annual Plumbing Inspection on all your home’s plumbing systems? Ask about the Abacus CLUB. The CLUB membership will give you the peace of mind that your plumbing system is working at top efficiency. Our licensed plumbers will conduct an inspection of your home to look for and fix any potential plumbing problems. 
AC air handler buzzing sounds. Do you hear a buzzing sound when you turn on the thermostat? The only thing that comes on in the house when you turn on the thermostat is the fan relay and fan in the air handler or furnace. Try switching the thermostat HEAT/COOL switch to OFF. Then switch the fan switch from AUTO to ON. The fan (only) should come on. If the air handler makes a buzzing sound, it probably has a bad fan relay or, more likely, blower fan.
I originally took off one star because of the SNAFU with getting the part ordered.  When Alberto called me on the phone he admitted the person had "gotten busy with other things" and apologized.  THAT was taking the high road and I was impressed by that.  Sadly, for reasons I won't guess at, Alberto has decided to take the low road in his comments and imply that they got the part as quickly as possible.  Well, we called at 2:30 so did someone spend six and a half hours finding the part??  That seems very doubtful.

Every Trane system is tested in some of the most extreme conditions found in nature to ensure they’re truly unstoppable – like freezing conditions in our System Extreme Environmental Test (SEET) lab. That’s where engineers put units through five years of wear and tear in just a few months, to get a product you can count on to run through anything. We never settle, so they never stop.


Portland, OR ServicesThe Sash Man Window Repair. Window Replacement & Installation Company - Portland, ORPest Control Contractors Portland, ORPortland, OR Best Foundation RepairPortland, OR Remodeling ContractorAppliance & Refrigeration HospitalPortland, OR Roofing ContractorFurniture Builders Portland, ORNatural Woodcrafters IncPortland, OR HandymanPortland, OR Painter
With the split system, the evaporator coil is connected to a remote condenser unit using refrigerant piping between an indoor and outdoor unit instead of ducting air directly from the outdoor unit. Indoor units with directional vents mount onto walls, suspended from ceilings, or fit into the ceiling. Other indoor units mount inside the ceiling cavity, so that short lengths of duct handle air from the indoor unit to vents or diffusers around the rooms.
We will get into specifics later, but there are plenty of recommended maintenance items all homeowners should strongly consider if you want you to extend the lifespan of your AC unit. Furthermore, regular maintenance prevents certain repairs less organized homeowners see every few years. Some easy and highly recommended AC unit maintenance tasks include:
A.J. LeBlanc Heating, A/C, Plumbing & Electric is a full-service HVAC, electrical & plumbing contractor. The LeBlanc family has been installing and servicing residential equipment since 1928! To this day we live by our original core values of quality workmanship & customer service. We pride ourselves in quality workmanship which is why "Nobody can quite compare to A.J. LeBlanc Heating & Air!" Call A.J. LeBlanc Heating, Cooling, Plumbing & Electric today for a free estimate. We service Southern NH, including Manchester NH, Concord NH, Nashua NH and Salem NH.
ABM (NYSE: ABM) is a leading provider of facility solutions with revenues of approximately $5.5 billion and more than 130,000 employees in 350+ offices throughout the United States and various international locations. ABM's comprehensive capabilities include janitorial, electrical & lighting, energy solutions, facilities engineering, HVAC & mechanical, landscape & turf, mission critical solutions and parking, provided through stand-alone or integrated solutions. ABM provides custom facility solutions in urban, suburban and rural areas to properties of all sizes - from schools and commercial buildings to hospitals, data centers, manufacturing plants and airports. ABM Industries Incorporated, which operates through its subsidiaries, was founded in 1909. For more information, visit www.abm.com.
Technicians who specialize in new installation work may experience periods of unemployment when the level of new construction activity declines. Maintenance and repair work, however, usually remains relatively stable. Business owners and homeowners depend on their climate-control or refrigeration systems year round and must keep them in good working order, regardless of economic conditions.
If the AC doesn’t turn off, it may be time to clean the condensing unit. Dirty condenser coils won’t give off heat efficiently and will keep the unit running.  Another possibility: The contacts on the outdoor run relay may have welded together—something that can happen over time because of frequent electrical arcing at the relay. Before checking the run relay, turn off the power to the furnace and the condensing unit. Next, disassemble the relay and pry apart the contacts. This should do the trick until you buy a replacement—which you should do soon.
New heating and cooling equipment installations present a wide variety of options that can save you money on your power bills and reduce the amount of HVAC maintenance and service that will ultimately be required over the life of your new unit. Energy-efficient options like heat pumps, two-stage furnaces, air-to-heat exchangers (HRVs), and programmable thermostats can all go a long way toward increasing efficiency and extending the life expectancy of your system.
“Air conditioners contain refrigerant, which allows the system to run efficiently, releasing heat from the air to cool it. Air conditioners are charged with refrigerant upon installation; a poor charge or a refrigerant leak can cause the system’s refrigerant level to fall below the proper amount. To remedy this, the home AC repair which is performed is a refrigerant recharge, accompanied by fixing the leak if that was the source causing low refrigerant levels.

Our Technicians are NATE Certified, licensed TACLA00078831E,  and will arrive in vehicles fully stocked so that the repair can be done the same day. When it comes to system performance, we are the pros. We have had extensive training in residential and commercial air balancing which means we can dial in your system to perform at maximum levels. We specialize in home or business air conditioning service and repair.


The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.

Evaporative coolers, sometimes called "swamp coolers", do not have a compressor or condenser. Liquid water is evaporated on the cooling fins, releasing the vapor into the cooled area. Evaporating water absorbs a significant amount of heat, the latent heat of vaporisation, cooling the air. Humans and animals use the same mechanism to cool themselves by sweating.
Throughout the coldest months of winter—especially in North America—a heating system repair is probably not something you want on your mind, but it likely will be if you need it on a bone-chilling day. You are in luck though, because Service Experts Heating & Air Conditioning is committed to doing expert quality furnace and heat pump repair, maintenance and installation through North America. It’s our job to make sure you are left with complete comfort in your home.
Before you service an air conditioner, make sure the unit is turned completely off by unplugging or shutting off the circuit breaker. Then, rake off any debris from the unit and use a soft brush to remove dirt from the outside cover. If the small copper pipe connecting the unit to the house feels hot, the unit’s coils likely needs to be washed. Remove the outside cover, cover the motor and wiring with a plastic sheet, and hose down the fins, coils, and inside of the unit. Finally, replace the cover when you’re done.
"Highly recommend! From the time I contacted them to make an appointment, to them showing up, troubleshooting the issue with my a/c unit, them verifying my warranty and driving to Grapevine to get the part, then back to Fort Worth to install it was LESS than 24 hours. Outstanding service, price and knowledge. I will only use this company from now on. Would give ten stars if possible."
×